大掺量固废3D打印建筑材料的研究
3D打印混凝土技术体系、工艺参数与固废资源化研究综述
三组初始化分组中的综述类文献合并于此:系统梳理挤出式3D打印的设备与工艺、胶凝材料与外加剂选择、打印参数对硬化性能的影响,碱激发打印硬化性能与地聚物砂浆新鲜态—可打印性关系,以及再生骨料、工业副产物、CDW在城市固废3D打印中的利用路径。共同点是提供宏观技术框架、术语体系与研究缺口清单,作为全部专题研究的总论基础,不涉及具体配合比或LCA核算。
- 3D Concrete Printing Review: Equipment, Materials, Mix Design, and Properties(G. Girskas, M. Kligys, 2025, Buildings)
- A Comprehensive Review on Effects of Material Composition, Mix Design, and Mixing Regimes on Rheology of 3D-Printed Geopolymer Concrete(P. Barve, Alireza Bahrami, Santosh Shah, 2024, The Open Construction & Building Technology Journal)
- Role of 3D Printed Concrete as a Sustainable Structure and Construction(Sadaqat Hayyat, M. Adeel, G. Akbar, Asad Abbas, S. Zaib, Muhammad Rehan Ahmed Khan, 2025, European Journal of Theoretical and Applied Sciences)
- Industrial Waste in 3D Printed Concrete: A Mechanistic Review on Rheological Control and Printability(Ruiyin Liu, Zhong-Ming Xiong, Xuan Chen, Qiong Jia, Jia-Rui Liu, Yue Liu, Junjie Zeng, Y. Zhuge, 2025, Journal of Building Engineering)
- Recycled Waste Materials Utilised in 3D Concrete Printing for Construction Applications: A Scientometric Review(Ali Mahmood, Nikos Nanos, David Begg, H. Dhakal, 2025, Buildings)
- Recycled Components in 3D Concrete Printing Mixes: A Review(Marcin Maroszek, Magdalena Rudziewicz, M. Hebda, 2025, Materials)
- Review Paper on Investigating the Hardened Properties of Extrusion Based 3D Concrete Printing with Agro-Industrial Waste Materials(N. Verma, 2024, International Journal for Research in Applied Science and Engineering Technology)
- Eco-friendly geopolymer materials: A review of performance improvement, potential application and sustainability assessment(Ji-Hui Zhao, Liang-Yu Tong, Boen Li, Tianhao Chen, Chun-Peng Wang, Gangqiang Yang, Ye Zheng, 2021, Journal of Cleaner Production)
- Fresh-State Characteristics of Geopolymer Mortars for 3D Printing: Mix Design, Rheology and Early-Age Performance(İbrahim Türkmen, Enes Ekinci, Fatih Kantarcı, Ergun Ekinci, Abdulrahman Ahmad Alyamani, M. Karakoç, Ramazan Demirboğa, Y. Ayaz, 2026, Polymers)
- Review of 3D-Printed Cementitious and Geopolymer Permanent Formwork for Concrete Structures(Muhammad Shaharyar Qaisar, H. Siad, M. Lachemi, Obaid Mahmood, M. Şahmaran, 2026, Materials)
固废基3D打印材料的生命周期评价与低碳可持续性量化
原分组中分散于三处(A9、B1、C6)的环境与经济性文献合并:以LCA、全球变暖潜势、碳/生态/水足迹与循环经济指标,量化再生骨料、油页岩灰—偏高岭土、替代性辅助胶凝材料对打印构件环境绩效的贡献,并讨论强度—碳排放—可打印性的权衡。与研究现状综述的区别在于其核心方法是定量环境核算而非技术梳理。
- Low-CO2 Concrete from Oil Shale Ash and Construction Demolition Waste for 3D Printing(Alise Sapata, Ella Spurina, Mohammed H. Alzard, Peteris Slosbergs, Hilal El-Hassan, M. Šinka, 2026, Journal of Composites Science)
- 3D Construction Printing Standing for Sustainability and Circularity: Material-Level Opportunities(Maria Teresa Saraiva P. F. Dias Fonseca, A. Matos, 2023, Materials)
- Environmental Footprint of 3D-Printed Concrete Using Recycled Materials(Claudia Muñoz-Sanguinetti, Mabel Vega-Coloma, V. Letelier, M. Marrero, R. García Alvarado, P. Wegertseder-Martínez, 2025, Sustainability)
- Sustainable utilization of waste in the 3D printed concrete(Jun-Bo Sun, Haihong Wang, Yu Zhang, Han Liu, Meng Zhang, Xiangyu Wang, 2024, Journal of Building Design and Environment)
- Review on sustainability in 3D concrete printing: focus on waste utilization and life cycle assessment(V. Sakhare, Neha Khairnar, Ulka Dahatonde, S. Mashalkar, 2025, Asian Journal of Civil Engineering)
- Toward Sustainable 3D Concrete Printing: A Critical Review of Waste-Derived Materials Across Binder, Geopolymer, and Aggregate Systems(K. Kamel, R. Shamass, Yen-Yu Lin, R. Jin, 2026, Applied Sciences)
- 3D Printed Concrete for Sustainable Construction: A Review of Mechanical Properties and Environmental Impact(Amer Hassan, T. Alomayri, Mohammed Faisal Noaman, Chun-Wei Zhang, 2025, Archives of Computational Methods in Engineering)
- Mechanical anisotropy, rheology and carbon footprint of 3D printable concrete: A review(Chaofan Wang, Bing Chen, T. Vo, M. Rezania, 2023, Journal of Building Engineering)
碱激发/地聚合物胶凝体系的前驱体设计、激发方式与力学—微观结构
合并原A2、B3、C1中偏重材料体系本体设计的文献:以粉煤灰、矿渣、铜渣、金尾矿、MSWI底灰、打印废料等大掺量工业固废为前驱体,研究单组分/双组分与混杂激发剂、水胶比、骨胶比与低浆体体积设计对强度、各向异性及C-A-S-H/C-(N)-A-S-H产物的影响,目标是完全替代高碳水泥并实现规模化放大。组内不含以流变—凝结窗口为主线的调控研究(另设专组)。
- Study of 3D printed concrete with low-carbon cementitious materials based on its rheological properties and mechanical performances(Wei-Jiu Cui, Tianheng Wang, Xinfa Chen, Wenkai Shen, Xinyu Shi, Sheng Wang, P. Zhang, 2023, Journal of Sustainable Cement-Based Materials)
- 3D concrete printing of eco-friendly geopolymer containing brick waste(K. Pasupathy, Sayanthan Ramakrishnan, J. Sanjayan, 2023, Cement & Concrete Composites)
- Development and optimization of geopolymer-based 3D printing materials utilizing industrial solid waste: Rheological properties and practical applications(Ke-Heng Pan, Yinhan Cheng, Guangfei Qu, Zheng Yuan, Guojun Liu, 2025, Construction and Building Materials)
- Roles of hybrid activators in improving the early-age properties of one-part geopolymer pastes(Yan-Shuai Wang, Yazan Alrefaei, Jian-Guo Dai, 2021, Construction and Building Materials)
- Study on the Properties of Alkali-activated Gold Tailings 3D Printing Concrete(De-Peng Wang, 2025, Academic Journal of Science and Technology)
- DEVELOPMENT OF ECO-FRIENDLY ALKALI-ACTIVATED CONCRETE FOR 3D PRINTING(Kito Luyten, M. Mohan, Yu-Bo Sun, Saeid Ghorbani, Stijn Matthys, K. Van Tittelboom, 2024, Sustainable Construction Materials and Technologies)
- Study on the Performance of 3D-Printed Alkali-Activated GGBS and FA Mortar with Steel Slag Sand as Aggregate(Feng Chen, Wei-Wei Huang, Zhi-Yuan Li, Guo-Hua Li, 2026, Journal of materials in civil engineering)
- Rheological, mechanical and fire resistance performance of waste glass activated geopolymers for concrete 3D printing(Sayanthan Ramakrishnan, Kirubajiny Pasupathy, A. Manalo, J. Sanjayan, 2025, Journal of Sustainable Cement-Based Materials)
- Sustainable Construction by Utilization of Municipal Solid Waste Incineration - Bottom Ash (MSWIBA) as Material for Developing One-Part 3D Printed Geopolymer Concrete(P. Barve, Santosh Shah, Deep Upadhyaya, 2026, International Journal of Civil Engineering)
- Upscaling of Copper Slag-Based Geopolymer to 3D Printing Technology(B. Kozub, M. Sitarz, S. Gądek, C. Ziejewska, K. Mróz, I. Hager, 2024, Materials)
- Alkali-activated slag with 3D printing waste: Self-heating potential pretests(L. Fiala, M. Brázda, M. Petříková, M. Keppert, M. Böhm, R. Černý, 2023, AIP Conference Proceedings)
- Understanding the relationship between composition and rheology in alkali-activated binders(N. Kozhukhova, I. Shurakov, M. Kozhukhova, M. Elistratkin, N. Alfimova, 2021, Journal of Physics, Conference Series)
碱激发/无水泥体系的凝结时间、流变行为与可打印性窗口调控
聚焦碱激发/地聚物体系特有问题:反应快、凝结时间与打印窗口难匹配。通过缓凝组分(硼砂、蔗糖、纳米黏土等)、单组分与双组分活化方案、温度与前驱体细度调节凝结与结构建立速率,建立屈服应力、触变性与挤出性、层间可建造性的关系。与原A2的'前驱体配比—强度'主线互补,专门解决'快凝—可打印'矛盾。
- Investigation on working properties and microstructural characteristics of activated geopolymer matrix composites for 3D printing(Zhaoqi Yin, Guang Yang, Jian-Ting Li, Yang Shen, Yi-Hang Cheng, Jalin Fu, Yan Shi, 2026, Journal of Physics, Conference Series)
- Optimization of One-Part Alkali-Activated Concrete for Extrusion-Based 3D Printing Through Integrated Performance Evaluation(Haiyang Li, Ai-Zhong Luo, Xiao-Zhong Zhang, Xiaomeng Ma, Jin-Sheng Han, Bo Cui, Wei Chen, 2026, Buildings)
- Advancing cementless composites by contrasting the thermomechanical performance and printability of additively manufactured and cast structures(Sung-Ching Chen, Marek Hebda, M. Szechyńska-Hebda, Wei Lin, 2026, Materials Science)
- Determination of the Geopolymer Binders Setting Time for 3D Printing Technology(S. Gądek, M. Nykiel, T. Tepla, L. Bohun, Z. Duriagina, D. Mierzwiński, 2024, Abstracts for the 5th World Conference on Chemistry and Chemical Engineering and 5th World Conference on Advanced Materials, Nanoscience and Nanotechnology)
- Formulation of alkali-activated fly ash-slag binders for 3D concrete printing(Kala Kondepudi, K. Subramaniam, 2021, Cement & Concrete Composites)
- One-Part vs. Two-Part Alkali-Activated GGBFS Mortars: Influence of Water-to-Binder Ratio on Extrusion-Based 3D Concrete Printing(Rafaela K. R. Silva, Andreas Appel, Nico Obermeier, T. Stengel, Andrea Kustermann, P. R. Borges, 2026, Infrastructures)
- Sustainable geopolymer binders for extrusion-based 3D printing: rheology, microstructure, and printability under ambient and sub-ambient conditions(L. Ricciotti, Daniele Lucariello, Valeria Perrotta, A. Apicella, R. Aversa, 2026, Progress in Additive Manufacturing)
建筑与拆除固废(CDW)及城市固废基3D打印材料的制备、流变适配与高掺量优化
合并原B2与C3中的CDW/城市固废主线:以废砖、废陶瓷、废玻璃、再生细骨料与再生混凝土粉、混合水泥、市政固废为主体原料,研究材料提取与形貌特征、经验流变测试与挤出性/建造性评价,以及用多目标自适应优化提升固废掺量与建造性的协同水平,验证全CDW体系免外加剂打印的可行性。与原'综述'组的CDW综述文献呼应但以实验数据为主。
- 3D-printable materials containing construction and demolition waste: a review(Ping Lyu, Da-You Luo, Emine Ozdogru, Oğuzhan Şahin, 2026, Innovative Infrastructure Solutions)
- Construction and demolition waste-based geopolymers suited for use in 3-dimensional additive manufacturing(Oğuzhan Şahin, H. İlcan, Anıl Tolga Ateşli, A. Kul, G. Yıldırım, M. Şahmaran, 2021, Cement & Concrete Composites)
- Construction and demolition waste in 3D printing of alkali-activated materials: potential effects of incorporation(D. A. G. Orrego, M. T. Barraza, F. J. G. Mendes, H. Colorado, M. Marvila, A. G. D. de Azevedo, 2026, International Journal of Environmental Science and Technology)
- Recent advances in CDW-based geopolymers: A review of mechanical performance, structural application, 3D printing, durability and sustainability.(O. Mahmoodi, H. Siad, M. Lachemi, M. Şahmaran, 2025, Journal of Environmental Management)
- Evaluating the use of recycled fine aggregates in 3D printing: a systematic review(P. V. Reddy, G. Nakkeeran, Dipankar Roy, George Uwadiegwu Alaneme, 2024, Discover Applied Sciences)
- CONSTRUCTION AND DEMOLITION WASTE FINE AGGREGATE FOR SUSTAINABLE 3D PRINTABLE CONCRETE: RHEOLOGICAL AND MECHANICAL PERFORMANCE(M. Osta, F. Mukhtar, 2026, Proceedings of International Structural Engineering and Construction)
- Preparation of 3D-Printed Concrete from Solid Waste: Study of the Relationship between Steel Slag Characteristics and Early Performance in 3D Printing(Wanting Zhao, Yu Zhao, Ling-Li Zhu, Xuemao Guan, 2024, Journal of materials in civil engineering)
- Multi-objective adaptive experimental approach for optimizing 3D concrete printing mixtures and parameters incorporating construction and demolition waste for sustainable construction(Thomas Tawiah Baah, H. Kim, M. Latypov, 2025, Discover Concrete and Cement)
- Rheological properties and compressive strength of construction and demolition waste-based geopolymer mortars for 3D-Printing(H. İlcan, O. Şahin, A. Kul, G. Yıldırım, M. Şahmaran, 2022, Construction and Building Materials)
再生骨料与多源固废骨料替代、颗粒形貌—界面过渡区效应及固废预处理工艺
保留原A4的独特论点并补入固废预处理文献:以再生骨料、再生砖骨料、球形电炉渣、油污砂、贝壳类海相固废、建筑拆除垃圾替代天然砂石,研究颗粒堆积与骨料形貌/级配、含盐与油污等杂质对流动性、静态屈服应力、可建造性、力学强度及ITZ的影响,并纳入固废分选与预处理工艺对打印材料一致性的保障作用。与CDW组的区别在于以'骨料相'而非'胶凝相/整体配方'为研究核心。
- Printable concrete with multi-source recycled aggregates: particle packing design, rheological behavior, and 3D printing validation(Guido Silva, Marcell Tudela, Omar Rojas, Camila Llontop, Arnaud Perrot, Rafael Aguilar, 2026, Materials Structure)
- Effect of Spherical Electric Arc Slag on Solid Waste-Based 3D-Printed Concrete(Qi Lu, Su-Dong Hua, Hongfei Yue, 2025, Applied Sciences)
- Utilisation of Oil-Contaminated Sand in 3D-Printed Concrete: Rheological, Mechanical, and Microstructural Assessment(Sanjana Pokhrel, Rajab Abousnina, Nusrat Jahan Mim, Mizan Ahmed, Ardalan B. Hussein, Wen-Su Chen, 2026, Buildings)
- Mechanical Properties and Interfacial Transition Zone Microstructure Analysis of 3D Printed Concrete Utilizing Waste Cockle Shell Aggregate and PP Fiber Waste Fishing Net(Hyunju Oh, Jeewoo Suh, Ju-Hyeon Park, Tong-Seok Han, 2025, Journal of the Computational Structural Engineering Institute of Korea)
- Development of Eco-Friendly Construction Materials for 3D Printing Using Fly Ash and Demolition Waste(Marcin Maroszek, Magdalena Rudziewicz, Syed Samran Ali Shah, Doan Hung Tran, M. Hebda, 2025, Buildings)
- Improving the Effect of Calcined Salt Mud on Mechanical Properties of 3D Printing Materials Using Recycled Construction Aggregates(Yuntao Wang, Shangjin Jiang, Su-Dong Hua, Hongfei Yue, Ya-Nan Zhang, 2024, Applied Sciences)
- Industrial Waste Pretreatment Approach for 3D Printing of Sustainable Building Materials(Qaisar Munir, Sanaz Afshariantorghabeh, T. Kärki, 2022, Urban Science)
粉煤灰、矿渣、硅灰等辅助胶凝材料大掺量替代水泥的配合比与新鲜态—硬化性能
合并原B4与A5中的SCM主线,是文献体量最大的实验证据板块:在水泥基/波特兰-火山灰体系中以粉煤灰、矿渣、微硅粉与废粉大比例替代胶凝材料,系统研究水胶比、砂胶比、骨料级配、搅拌策略与掺量对挤出性、建造性、流变参数及强度、收缩、吸水等硬化性能的影响,属'配合比设计—性能验证'类研究。
- 3D Printed Concrete: Fresh and Hardened Properties(Marwah M. Thajeel, György L. Balázs, 2024, Periodica polytechnica. Civil engineering)
- Performance Requirements and Optimum Mix Proportion of High-Volume Fly Ash 3D Printable Concrete(H. Şahin, A. Mardani, Naz Mardani, 2024, Buildings)
- Development of a Novel Mixing Strategy for Set-on-demand Printing of One-part Geopolymer using Municipal Solid Waste Incineration Bottom Ash and Blast Furnace Slag(Syed Farasat Ali Shah, Shi-Peng Zhang, D. Xuan, Chi-Sun Poon, 2025, Journal of Building Engineering)
- Utilization of powders and fine aggregates from the recycling of construction and demolition waste in the 3D printing of Portland-based cementitious materials(R. Robayo-Salazar, Armando Vargas, Fabio Martínez, Ruby Mejía de Gutiérrez, 2024, Cleaner Materials)
- The effect of waste powder on the 3D printing performance of cement-based materials(Te Li, Laire Tier, 2024, Arabian Journal of Geosciences)
- Strength Characterisation of Fly Ash Blended 3D Printed Concrete Enhanced with Explainable Machine Learning(Imtiaz Iqbal, Waleed Bin Inqiad, Tala Kasim, Svetlana Besklubova, M. Adil, Mujib Rahman, 2025, Case Studies in Construction Materials)
- Influence of Slag/Fly Ash as Partial Cement Replacement on Printability and Mechanical Properties of 3D-Printed Concrete(Kuo-Chang Tseng, M. Chi, W. Yeih, Ran Huang, 2025, Applied Sciences)
- 3D printed concrete using Portland pozzolana cement - fly ash based(M. Ibrahim A, S. Kumar N, 2024, E3S Web of Conferences)
- Effect of fly ash and ground waste glass as cement replacement in concrete 3D-Printing for sustainable construction(Phebe Samrani, Yifang Cao, G. Fimbres Weihs, Eric Sanjaya, Ali Abbas, 2024, Frontiers in Built Environment)
- Designing 3D-printed concrete with ternary blended mortars incorporating fly ash and silica fume: effects of low water-binder ratios on workability and strength(K. Hasan, A. Alias, Mehedi Hasan, F. M. Yahaya, Khairul Fikri Muhammad, 2026, Innovative Infrastructure Solutions)
废玻璃粉、玄武岩岩粉、镁渣/磷酸镁钾与三元复合低碳胶凝粉体的功能化设计
保留原A5中被大组掩盖的独特方向:以废玻璃粉、玄武岩岩粉、煅烧污泥/镁渣改性的磷酸镁钾体系、建筑石膏基打印粉体以及三元固废/混杂水泥体系为对象,考察非常规固废粉体对水胶比、水化放热、抗折抗压强度与收缩/吸水的平衡作用,体现'粉体功能化+多源协同'的高掺量设计思路,区别于常规SCM替代研究。
- Basaltic Rock Dust as a Sustainable Supplementary Cementitious Material for 3D-Printed Concrete: From Mix Optimisation to Printing Performance(Brayden Weston, Rajab Abousnina, Nusrat Jahan Mim, Mizan Ahmed, Wen-Su Chen, 2026, Buildings)
- Influence of waste glass powder on printability and mechanical properties of 3D printing geopolymer concrete(Zhao-Liang Sheng, Bin-Rong Zhu, Jing-Ming Cai, Jin-Sheng Han, Yamei Zhang, Jin-Long Pan, 2024, Developments in the Built Environment)
- Valorisation of Industrial Wastes in Magnesium Potassium Phosphate Cements for Extrusion-Based 3D Printing(P. Padilla-Encinas, Jose Fernando Corani, Jaime F. Cuevas, Ana Guerrero, R. Fernández, 2026, Minerals)
- Preparation of architectural 3D printing material with a solid waste-derived sulfoaluminate matrix: A high-value conversion of solid waste(Y. Mao, Jia-Zheng Zhang, Han Wu, Yan-Ming Huang, Xu-Jiang Wang, Jing-Wei Li, Jing Sun, Wen-Long Wang, 2023, Case Studies in Construction Materials)
- High-strength low paste volume ternary-blended 3D printed one-part geopolymer concrete: rheology, hardened mechanics, and microstructure(B. Ajayi, G. V. van Zijl, A. J. Babafemi, 2026, Journal of Sustainable Cement-Based Materials)
- Development of Sustainable 3D Printable Ternary Composite(Alise Sapata, Māris Šinka, G. Šahmenko, G. Bumanis, Liga Puzule, Peteris Slosbergs, D. Bajare, 2024, CONECT. International Scientific Conference of Environmental and Climate Technologies)
- 3D Printing of Hybrid Cements Based on High Contents of Powders from Concrete, Ceramic and Brick Waste Chemically Activated with Sodium Sulphate (Na2SO4)(R. Robayo-Salazar, Fabio Martínez, Armando Vargas, Ruby Mejía de Gutiérrez, 2023, Sustainability)
磷石膏基固废复合胶凝材料的配比设计、协同激活与强度提升机理
原A3为独立且无可替代的固废体系(硫酸钙基),单列保留:以磷石膏为主要固废组分,与矿渣、粉煤灰、电石渣、再生混凝土粉协同激活,采用响应面法等优化替代率与配比,研究强度提升机理、浆体稳定性与打印开放时间,避免被硅酸盐/碱激发大组吞并而丢失石膏基路线的特殊性。
- Strength Enhancement of 3D-Printed Phosphogypsum Concrete Based on Synergistic Activation of Multi-Solid Wastes(Junjie Li, Yangbo Li, Xianqiang Ge, K. Li, Ya-Hui Yang, Shuo Wang, 2026, Materials)
- Mix Proportion Design and Performance Regulation of 3D-Printing Phosphogypsum-Based Geopolymer Paste(P. Zhu, Hailong Tan, Jun-Tao Ma, Jian-Guang Yin, Binbin Zhang, Yuping Tong, 2026, Buildings)
打印材料流变调控、触变恢复与形状稳定性控制(含外加剂与纤维)
合并原A6与C2:以流变学为核心方法,通过膨润土、纳米黏土、CMC、纤维素醚、减水/增稠剂及贝壳与墨鱼骨粉、纤维等调节屈服应力、塑性黏度、触变恢复与结构重建速率,建立新鲜态参数与挤出性、条带宽度、开放时间、层间变形之间的定量关联。与第4组的区别是面向通用(含水泥基)体系的打印性调控,而非专门解决碱激发快凝问题。
- Rheology and Shape Stability Control of 3D-Printed White Calcium Sulfoaluminate Cement Composites Containing Oyster Shell and Cuttlebone Powder(Xin Qu, Qin-Yuan Wang, Jiafeng Kong, Jun-Yue Wang, Jie Wang, Xingang Xu, Yannan Zheng, He-Yang Wu, Mingxu Chen, 2026, Materials)
- Rheology control and 3D concrete printing with fly ash-based aqueous nano-silica enhanced alkali-activated binders(Tippabhotla A. Kamakshi, K. Subramaniam, 2024, Materials Structure)
- Evaluation of Fresh Properties of High Calcium Content Fly Ash-based Alkali-Activated 3D-Printed Mortar(Fareh Abudawaba, Eslam Gomaa, Ahmed A. Gheni, Dimitri Feys, M. ElGawady, 2025, Journal of Building Engineering)
- Study on 3D printing of novel alkali-activated materials: rheological properties, printing results, and printing prediction model(Yan-Fang Zhang, Rui-Xing Wang, Jiao-Jiao Ni, 2026, Reviews on Advanced Materials Science)
- Experimental study on printability of solid waste concrete based on 3d printing technology(Yingming Liang, Jincheng He, Li-Ke Niu, Jun-Wei Chen, Hong-Zhi Wang, Peng Chen, 2025, Journal of Physics, Conference Series)
- Investigation of the Impact of Material Rheology on the Interlayer Bonding Performance of Solid Waste 3D-Printed Components(Yi-Fan Li, Shui-Sheng Chen, Liuhua Yang, Chuan Guo, Zhen-Tao Li, Youliang Chen, 2025, Buildings)
- Tailoring rheology and mechanical properties of 3D printed mortars with nanoclays and superplasticizer(Wen Si, L. Carr, Mehran Khan, C. Mcnally, 2026, Reviews on Advanced Materials Science)
- Rheological and mechanical properties of polyformaldehyde fiber reinforced 3D-printed high-strength concrete with the addition of fly ash(Su-Rong Luo, Wenhao Jin, Weihong Wu, Kai-Jian Zhang, 2024, Journal of Building Engineering)
打印硬化体的层间界面粘结、力学各向异性与永久模板界面协同受力
合并原B5、C4与A7中的界面—各向异性论点:分析打印方向、层间间隔时间、骨料粒径与喷嘴尺寸、纤维与废骨料引入对层间粘结强度、抗压抗折强度、弹性模量与弯曲韧性的影响,并考察3D打印永久模板与后浇混凝土的界面协同受力。突出打印工艺造成的层状正交异性这一独特力学问题。
- Mechanical performance and anisotropic analysis of rubberised 3D-printed concrete incorporating PP fibre(Xin Lyu, M. Elchalakani, Xiangyu Wang, Jun-Bo Sun, Bo Huang, M. Saafi, Bin-Rong Zhu, Ziqing Wei, Yu-Fei Wang, 2024, Environmental science and pollution research international)
- Effects of Aggregate Size and Nozzle Diameter on Printability and Mechanical Properties of 3D Printed Ferronickel Slag–GGBFS Concrete(Su Wang, Xing Wang, Xue-Yuan Yan, Shanghong Chen, 2025, Materials)
- Influence of Printing Direction and Interlayer Printing Time on the Bond Characteristics and Hardened Mechanical Properties of Agro-Industrial Waste–Based 3D Printed Concrete(Ajay Chourasia, Biswajit Pal, Ashish Kapoor, 2025, Journal of materials in civil engineering)
- Adhesion performance of alkali-activated material for 3-dimensional printing of tunnel linings at different temperatures(Ya-Xin Tao, Xiaodi Dai, G. de Schutter, K. Van Tittelboom, 2024, Frontiers of Structural and Civil Engineering)
- Optimization and Performance Study of 3D Printed Concrete Mixture for Underground Utility Tunnels(Peixi Guo, Han-Wen Zhang, Enmu Ge, Ming Lin, Hang Jia, Yao Zhang, Xin-Yu Fan, 2026, Buildings)
- Basalt fiber reinforced alkali-activated cementitious composite for low-carbon 3D printing by using fly ash, blast furnace slag and iron tailings(Chao Li, Na Zhang, You-Peng Zhang, Yi-Di Wang, Jia-Le Zhang, Lei Yang, Jian-Cong Zhang, Yi-He Zhang, 2026, Journal of Building Engineering)
孔结构、冻融与湿热耐久、高温抗火安全及断裂性能评价
合并原A7、B5、C4中服役性能与安全评价文献:以孔结构分析为桥梁,考察冻融循环、湿热—热力学耦合、100–600 ℃高温下的质量损失、开裂与耐火退化,以及闭合形式断裂模型对打印裂纹的评估,为固废基打印构件的耐久性与结构安全提供依据。与上一组相比关注的是环境作用与失效机理而非界面几何效应。
- Mechanical Properties and Freezing and Thawing Behavior of 3D Printing Concrete Containing Recycled Fine Aggregates from Construction and Demolition Waste(2024, International Conference on Cognitive Modelling)
- Corrigendum to “Enhancing thermo-mechanical and moisture properties of 3D-Printed concrete through recycled ultra-fine waste glass powder” [J. Clean. Prod. 480 (2024) 144121](Jian-Nan Li, Amardeep Singh, Ya-Song Zhao, Jing-Ting Sun, V. W. Tam, Jian-Zhuang Xiao, 2025, Journal of Cleaner Production)
- Enhancing thermo-mechanical and moisture properties of 3D-Printed concrete through recycled ultra-fine waste glass powder(Jian-Nan Li, Amardeep Singh, Ya-Song Zhao, Jing-Ting Sun, V. W. Tam, Jian-Zhuang Xiao, 2024, Journal of Cleaner Production)
- Advancing fire safety in buildings: performance evaluation of conventional, 3D‑printed and agro-industrial waste-based concrete(N. K. Banjara, Ajay Chourasia, 2026, Sustainable and Resilient Infrastructure)
- Mechanical Properties and Fire Resistance of 3D-Printed Cementitious Composites with Plastic Waste(Walid Yaqub, F. Aslani, 2024, International Journal of Concrete Structures and Materials)
- Closed-form fracture model for evaluating crack resistance of 3D printed fiber-reinforced alkali-activated slag/fly ash recycled sand concrete(Zheng-Yuan Chen, Shu-Tong Yang, Qi Liu, Ming-Qi Xu, Sheng Wang, Tian Lan, 2024, Journal of Building Engineering)
- Pore structure analysis and durability performance of sustainable 3D printed concrete incorporating fly ash and limestone calcined clay based binders(Zinnia Kaur, S. Goyal, N. Kwatra, T. K. Bera, 2025, Construction and Building Materials)
机器学习预测模型与原位传感监测驱动的智能设计与性能表征
合并原A8与C5两个小组合并为一个智能化手段板块:一方面用基因表达式编程(GEP)与可解释机器学习建模打印参数与材料组成对劈裂抗拉/抗压强度的非线性影响并输出显式公式与规则;另一方面通过嵌入式PZT传感器实时监测打印过程中的水化、凝结与刚度演化,共同减少试错试验量、提升大掺量固废配方设计效率。
- Interpretable model and explicit formula for 3D printed recycled aggregate concrete strength prediction(Ti-Lin Wang, Chao-Lin Liu, Chao Zhu, Wen-Xuan Zhu, Hua-Wei Liu, 2024, Journal of Building Design and Environment)
- Interpretable Machine Learning for Compressive and Flexural Strength Prediction of Fly Ash Blended 3D Printed Concrete with Uncertainty Quantification(Jia Chen, Zhi-Cheng Liao, Meng-Di Hou, Jian-Bo Huang, 2026, Computers, Materials & Continua)
- In situ embedded PZT sensor for monitoring 3D concrete printing: application in alkali-activated fly ash-slag geopolymers(A. Kocherla, Tippabhotla A. Kamakshi, K. Subramaniam, 2021, Smart materials and structures (Print))
- Machine Learning-Based Predictive Model for Tensile and Flexural Strength of 3D-Printed Concrete(A. Ali, Raja Dilawar Riaz, U. Malik, Syed Baqar Abbas, M. Usman, M. Shah, In-Ho Kim, Asad Hanif, Muhammad Qasim Faizan, 2023, Materials)
固废基3D打印材料的泡沫化、构件构型优化与离网/建筑工程应用
合并原B6与C3中的应用导向文献:从材料走向构件与场景,包括工业废渣基地聚合物泡沫打印、废弃物地聚合物保温墙体内部构型优化、铺路石与建筑体系原型、加性制造安全/应急材料以及离网现场自主打印与建筑应用示范,体现大掺量固废3D打印的工程落地与低碳效益,补足被其他分组弱化的'规模化应用'论点。
- Robotic 3D Printing of Geopolymer Foam for Lightweight and Insulating Building Elements(P. Bedarf, A. Szabo, M. Zanini, B. Dillenburger, 2023, 3D Printing and Additive Manufacturing)
- Optimization of Internal Patterns in 3D-Printed Walls to Control Heat Transfer and Embodied Impact(A. Kul, 2025, Black Sea Journal of Engineering and Science)
- Advancements in Additively Manufactured Safety Materials: Energy-Efficient 3D Printing Solutions for Critical Infrastructure(S. Khan, Muammer Koç, 2024, Advances in Materials)
- Preparation and 3D printing building application of sulfoaluminate cementitious material using industrial solid waste(Chang-Zai Ren, Dongliang Hua, Yonghui Bai, Shuang Wu, Yong-Gang Yao, Wen-Long Wang, 2022, Journal of Cleaner Production)
- Prototype of Paving Stones Based on Construction and Demolition Waste(Jonathan Xavier Moreno-Cabrera, Gerardo Silva-Montes, Saraí María Martínez-Mendoza, Atalía Luna-Pérez, Vicente Morales-Castillo, Rosa Elena Hernández-Acevedo, Martha Hilaria Bartolo-Aleman, Danny Adolfo Cordova-Mireles, Luis Ángel Santos-Pineda, Manuel Gómez-Sandoval, Omar Robledo-Cabrera, Marcos Tereso Jiménez-Ortiz, L. H. Robledo-Taboada, 2026, International Journal of Scientific Research in Science and Technology)
- Architectural, construction and technological system 3D – printing of small-sized building products and structures for low-rise residential housing(M. Savytskyi, A. Savytskyi, O. Savytskyi, T. Shevchenko, O. Savytskyi, 2026, Journal of Physics, Conference Series)
三组初始化分组共含103篇不重复文献,合并后按"总论—可持续评价—胶凝体系—固废来源—配合比与粉体—功能与性能评价—智能手段—工程应用"的链条重组为14个并列分组:(1)技术体系、固废利用与可打印性地聚合物新鲜态研究综述;(2)生命周期评价与碳/生态足迹可持续性分析;(3)碱激发/地聚物体系的前驱体设计、激发方式与力学—微观结构;(4)碱激发/无水泥体系的凝结—流变—可打印性调控;(5)建筑与拆除固废(CDW)及城市固废基材料的制备与资源化;(6)再生骨料与多源固废骨料替代、颗粒形貌、界面过渡区与固废预处理;(7)粉煤灰-矿渣-硅灰等辅助胶凝材料大掺量替代水泥的配合比与新鲜态—硬化性能;(8)废玻璃粉、玄武岩岩粉、镁渣/磷酸镁钾及三元复合低碳胶凝粉体;(9)磷石膏基固废复合胶凝材料配比设计与强度提升;(10)打印材料流变调控、触变恢复与形状稳定性;(11)层间界面、各向异性与永久模板界面协同受力;(12)冻融/湿热耐久、高温抗火、孔结构与断裂性能;(13)机器学习预测模型与原位传感智能表征;(14)泡沫化、构件功能设计与离网/建筑应用。合并原则是:保留"综述"与"LCA"两条贯穿性主线独立成组,避免与环境评价混入技术综述;将"胶凝体系设计(配方—水化—强度)"与"打印性/流变调控"分离以消除交叉;把固废来源(CDW、再生骨料、SCM、特种粉体、磷石膏)分列成并列专题,避免形成"大而笼统"的固废大组;同时补齐被三组均弱化的"孔结构与断裂模型""永久模板界面协同受力""固废预处理与分选工艺"等论点。
三组初始化分组中的综述类文献合并于此:系统梳理挤出式3D打印的设备与工艺、胶凝材料与外加剂选择、打印参数对硬化性能的影响,碱激发打印硬化性能与地聚物砂浆新鲜态—可打印性关系,以及再生骨料、工业副产物、CDW在城市固废3D打印中的利用路径。共同点是提供宏观技术框架、术语体系与研究缺口清单,作为全部专题研究的总论基础,不涉及具体配合比或LCA核算。相关文献:G. Girskas et. al, 2025 等 10 篇文献
原分组中分散于三处(A9、B1、C6)的环境与经济性文献合并:以LCA、全球变暖潜势、碳/生态/水足迹与循环经济指标,量化再生骨料、油页岩灰—偏高岭土、替代性辅助胶凝材料对打印构件环境绩效的贡献,并讨论强度—碳排放—可打印性的权衡。与研究现状综述的区别在于其核心方法是定量环境核算而非技术梳理。相关文献:Alise Sapata et. al, 2026 等 8 篇文献
合并原A2、B3、C1中偏重材料体系本体设计的文献:以粉煤灰、矿渣、铜渣、金尾矿、MSWI底灰、打印废料等大掺量工业固废为前驱体,研究单组分/双组分与混杂激发剂、水胶比、骨胶比与低浆体体积设计对强度、各向异性及C-A-S-H/C-(N)-A-S-H产物的影响,目标是完全替代高碳水泥并实现规模化放大。组内不含以流变—凝结窗口为主线的调控研究(另设专组)。相关文献:Wei-Jiu Cui et. al, 2023 等 12 篇文献
聚焦碱激发/地聚物体系特有问题:反应快、凝结时间与打印窗口难匹配。通过缓凝组分(硼砂、蔗糖、纳米黏土等)、单组分与双组分活化方案、温度与前驱体细度调节凝结与结构建立速率,建立屈服应力、触变性与挤出性、层间可建造性的关系。与原A2的'前驱体配比—强度'主线互补,专门解决'快凝—可打印'矛盾。相关文献:Zhaoqi Yin et. al, 2026 等 7 篇文献
合并原B2与C3中的CDW/城市固废主线:以废砖、废陶瓷、废玻璃、再生细骨料与再生混凝土粉、混合水泥、市政固废为主体原料,研究材料提取与形貌特征、经验流变测试与挤出性/建造性评价,以及用多目标自适应优化提升固废掺量与建造性的协同水平,验证全CDW体系免外加剂打印的可行性。与原'综述'组的CDW综述文献呼应但以实验数据为主。相关文献:Ping Lyu et. al, 2026 等 9 篇文献
保留原A4的独特论点并补入固废预处理文献:以再生骨料、再生砖骨料、球形电炉渣、油污砂、贝壳类海相固废、建筑拆除垃圾替代天然砂石,研究颗粒堆积与骨料形貌/级配、含盐与油污等杂质对流动性、静态屈服应力、可建造性、力学强度及ITZ的影响,并纳入固废分选与预处理工艺对打印材料一致性的保障作用。与CDW组的区别在于以'骨料相'而非'胶凝相/整体配方'为研究核心。相关文献:Guido Silva et. al, 2026 等 7 篇文献
合并原B4与A5中的SCM主线,是文献体量最大的实验证据板块:在水泥基/波特兰-火山灰体系中以粉煤灰、矿渣、微硅粉与废粉大比例替代胶凝材料,系统研究水胶比、砂胶比、骨料级配、搅拌策略与掺量对挤出性、建造性、流变参数及强度、收缩、吸水等硬化性能的影响,属'配合比设计—性能验证'类研究。相关文献:Marwah M. Thajeel et. al, 2024 等 10 篇文献
保留原A5中被大组掩盖的独特方向:以废玻璃粉、玄武岩岩粉、煅烧污泥/镁渣改性的磷酸镁钾体系、建筑石膏基打印粉体以及三元固废/混杂水泥体系为对象,考察非常规固废粉体对水胶比、水化放热、抗折抗压强度与收缩/吸水的平衡作用,体现'粉体功能化+多源协同'的高掺量设计思路,区别于常规SCM替代研究。相关文献:Brayden Weston et. al, 2026 等 7 篇文献
原A3为独立且无可替代的固废体系(硫酸钙基),单列保留:以磷石膏为主要固废组分,与矿渣、粉煤灰、电石渣、再生混凝土粉协同激活,采用响应面法等优化替代率与配比,研究强度提升机理、浆体稳定性与打印开放时间,避免被硅酸盐/碱激发大组吞并而丢失石膏基路线的特殊性。相关文献:Junjie Li et. al, 2026 等 2 篇文献
合并原A6与C2:以流变学为核心方法,通过膨润土、纳米黏土、CMC、纤维素醚、减水/增稠剂及贝壳与墨鱼骨粉、纤维等调节屈服应力、塑性黏度、触变恢复与结构重建速率,建立新鲜态参数与挤出性、条带宽度、开放时间、层间变形之间的定量关联。与第4组的区别是面向通用(含水泥基)体系的打印性调控,而非专门解决碱激发快凝问题。相关文献:Xin Qu et. al, 2026 等 8 篇文献
合并原B5、C4与A7中的界面—各向异性论点:分析打印方向、层间间隔时间、骨料粒径与喷嘴尺寸、纤维与废骨料引入对层间粘结强度、抗压抗折强度、弹性模量与弯曲韧性的影响,并考察3D打印永久模板与后浇混凝土的界面协同受力。突出打印工艺造成的层状正交异性这一独特力学问题。相关文献:Xin Lyu et. al, 2024 等 6 篇文献
合并原A7、B5、C4中服役性能与安全评价文献:以孔结构分析为桥梁,考察冻融循环、湿热—热力学耦合、100–600 ℃高温下的质量损失、开裂与耐火退化,以及闭合形式断裂模型对打印裂纹的评估,为固废基打印构件的耐久性与结构安全提供依据。与上一组相比关注的是环境作用与失效机理而非界面几何效应。
合并原A8与C5两个小组合并为一个智能化手段板块:一方面用基因表达式编程(GEP)与可解释机器学习建模打印参数与材料组成对劈裂抗拉/抗压强度的非线性影响并输出显式公式与规则;另一方面通过嵌入式PZT传感器实时监测打印过程中的水化、凝结与刚度演化,共同减少试错试验量、提升大掺量固废配方设计效率。相关文献:Ti-Lin Wang et. al, 2024 等 4 篇文献
合并原B6与C3中的应用导向文献:从材料走向构件与场景,包括工业废渣基地聚合物泡沫打印、废弃物地聚合物保温墙体内部构型优化、铺路石与建筑体系原型、加性制造安全/应急材料以及离网现场自主打印与建筑应用示范,体现大掺量固废3D打印的工程落地与低碳效益,补足被其他分组弱化的'规模化应用'论点。相关文献:P. Bedarf et. al, 2023 等 6 篇文献
总计 103 篇相关文献
3D printing technology is a new intelligent construction technology emerging in recent years. It has the characteristics of flexibility, convenience, and green environmental protection, and is widely used in the construction field. In response to the national call for low carbon and environmental protection, this paper carried out an experimental study on the printability of solid waste concrete based on 3D printing technology. Through the printing height, strip width, printing opening time, and flow expansion test, the effects of the number of additives such as water reducer, fiber, and thickener and the water-binder ratio on the printability of solid waste mixture were analyzed. The test results show that increasing the amount of water-reducing agent and water-binder ratio can significantly improve the flow performance of the material and prolong the printing opening time. However, considering the buildability of the material, the water-binder ratio should be 0.35, and the amount of water-reducing agent should not exceed 1%; The effect of fiber and thickener is similar. The addition of both will improve the construction performance of the material, but at the same time will lead to a decrease in the fluidity of the mixture. Therefore, the content of fiber and thickener should not exceed 0.50% and 0.04%, respectively; The construction height, strip width, and opening time of the mixture are linearly correlated with the fluidity, and the printability of the material can be evaluated by the fluidity. The fluidity of the test solid waste mixture should be 155 ˜ 182 mm.
No abstract available
No abstract available
With the rapid advancement of 3D printing technology in low-carbon construction, the constructability of 3D printing materials has increasingly garnered attention. The constructability of these materials is intrinsically linked to their rheological properties. Therefore, this paper investigates the impact of additives, specifically hydroxypropyl methylcellulose (HPMC) and polycarboxylate superplasticizer (PCE), on the rheological properties of materials. The findings indicated that HPMC significantly increased both shear stress and apparent viscosity while also enhancing the thixotropic loop area. In contrast, PCE was found to reduce viscosity and yield stress, thereby improving fluidity and plasticity. The judicious incorporation of PCE (less than 0.003) and HPMC (less than 0.002) can enhance the rheological properties of the printing material, thereby improving the stability and interlayer bonding characteristics of the 3D printing structure. However, an excessive amount will result in a reduction in fluidity and cohesion, adversely impacting the printing quality. At this stage, the occurrence of cracks increases, which is detrimental to interlayer adhesion. Therefore, the judicious control of the proportions of PCE and HPMC can enhance the fluidity and viscosity of the material, thereby improving interlayer bonding strength and print quality.
No abstract available
Using solid waste-based materials, such as recycled building aggregate (RCA), preparing 3D-printed materials can reduce costs but increase the water–cement ratio of the printed material, which reduces its mechanical performance. In order to solve the problem of mechanical properties decline caused by an increase in the w/c ratio, this experiment found that adding calcined salt mud (CSM) to the printing materials and changing the water-to-cement ratio from 0.37 to 0.4 CSM can ensure that the compressive strength of the printing materials remains basically unchanged. Moreover, through TG, SEM, and other microscopic data, it can be seen that calcium hydroxide in CSM can not only participate in the synergistic reaction of ethylene/vinyl acetate copolymer (EVA) and dust ash (DA), produce more NaOH, and promote the hydration of granulated blast furnace slag (GBFS) but also promote the formation of ettringite together with SO42− in solution, optimizing pore size distribution.
The ability of MSWIBA as a precursor for geopolymer mixtures amenable to 3D printing is explored in this research. In geopolymer binders, the MSWIBA is utilized in part substitution of fly ash. Investigations are conducted into how the MSWIBA content affects the fresh qualities of printed formulations, particularly setting time, rheological characteristics, and flowability. Additionally, using different amounts of MSWIBA in the mixture, the hardened characteristics of 3D printable MSWIBA geopolymer concrete are assessed. According to the test findings, the MSWIBA content in the mix has enhanced the fresh characteristics of the optimum 3D printed mix. Excellent early age yield stress and apparent viscosity are demonstrated by the optimum mixture with MSWIBA. The incorporation of MSWIBA up to 10 % has enhanced the compressive strength of 3D printable geopolymer concrete samples, whereas higher MSWIBA concentrations has led to a reduction in hardened properties. Lastly, the suggested one-part geopolymer can lessen the carbon emission and embodied energy by up to 11–38% in comparison with OPC concrete.
This article evaluates the synthesis, characterization and 3D printing of hybrid cements based on high (70%) contents of powders from concrete waste (CoW), ceramic waste (CeW) and red clay brick waste (RCBW) from construction and demolition waste. For the synthesis of the hybrid cements, 30% (by weight) of ordinary Portland cement (OPC) was added. Sodium sulphate (Na2SO4) (4%) was used as a chemical activator. The effect of the liquid/solid ratio on the properties in the fresh state of the mixes was studied by means of minislump, flowability index, and buildability tests. The compressive strength was evaluated at 3, 7, 28 and 90 days of curing at room temperature (≈25 °C), obtaining strengths of up to 30.7 MPa (CoW), 37.0 MPa (CeW) and 33.2 MPa (RCBW) with an L/S ratio of 0.30. The results obtained allowed selecting the CoW 0.30, CeW 0.33 and RCBW 0.38 mixes as optimal for carrying out 3D printing tests on a laboratory scale, successfully printing elements with good print quality, adequate buildability, and compressive strength (CoW 0.30 = 18.2 MPa, CeW 0.33 = 27.7 MPa and RCBW 0.38 = 21.7 MPa) higher than the structural limit (≥17.5 MPa) established for concrete by Colombian Regulations for Earthquake Resistant Construction (NSR-10).
This study examines magnesium potassium phosphate cements (MKPCs) modified with industrial wastes for extrusion-based 3D concrete printing, evaluating the rheological properties (workability, setting time), mechanical performance and printability of formulations incorporating secondary materials: Mg dross waste (up to 20 wt.%, replacing MgO), calcined sewage sludge (up to 10 wt.%, replacing KH2PO4), alternative fillers such as glass from municipal solid waste glass and from construction and demolition waste and ground blast furnace slag, benchmarked against volcanic ash. The baseline MKPC exhibited initial/final setting times of 34/109 min, good workability and compressive strengths of 29 MPa (1 day)/28 MPa (28 days). Optimal low-waste mixes (e.g., using municipal glass or 20 wt.% Mg dross) shortened the initial setting to 19–25 min (decreasing 24–42%), reduced the slump by 9–18% yet remained printable at laboratory-scale and achieved 1-day strengths > 23 MPa/28-day > 31 MPa (comparable or superior). Glass from municipal waste proved most promising, due to superior workability, lighter aesthetics and strength gains, supporting circular economy goals while substantially reducing material costs; higher waste levels compromised fluidity and buildability. Mineralogical analyses confirmed K-struvite formation alongside residual periclase, validating these formulations for upscaling sustainable 3D printing.
Mix Proportion Design and Performance Regulation of 3D-Printing Phosphogypsum-Based Geopolymer Paste
Building 3D printing technology exhibits remarkable construction advantages, with solid waste-based 3D printing slurry emerging as a research hotspot in the field. Phosphogypsum is compatible with diverse solid wastes for the fabrication of geopolymer, whereas its feasibility as a 3D printing material merits further investigation. In this study, calcium carbide slag (CS), ground granulated blast-furnace slag (GGBS), recycled concrete powder (RCP), and phosphogypsum (PG) underwent co-activation. The mix proportion received optimization via response surface methodology (RSM), and printability assessment proceeded based on the optimized proportion. Key conclusions include the following: PG exerts a role in optimizing the internal structure within the geopolymer matrix. The 28-day compressive strength of the composite geopolymer exceeds 25 MPa. Application as a 3D printing material facilitates enhancement of slurry stability in the later stage. Excessive PG addition elevates the shear stress and viscosity of the 3D printing paste, shortens the paste open time, and impedes paste extrusion and molding. Based on a comprehensive analysis of printability and the performance of printed specimens, the optimal mix proportion of the phosphogypsum-based geopolymer 3D printing paste was determined as follows: CS: 22.5%; GGBS: 45%; RCP: 22.5%; PG: 10%; W/b: 0.4.
Highlights What are the main findings? Proposes a novel route for large-scale phosphogypsum valorization in 3D-printed concrete. Achieves dual-function utilization of phosphogypsum as a binder and sulfate activator. Elucidates the synergistic mechanism between slag and phosphogypsum. What are the implications of the main findings? Resolves the inherent strength-deficiency of 3DPPGC. Integrates solid waste recycling with low-carbon construction goals. Paves the way for large-scale engineering deployment of phosphogypsum-based materials. Abstract Phosphogypsum (PG) is the main by-product of wet-process phosphoric acid production. Its annual global production reaches about 200 million tons, yet its utilization rate remains low. Consequently, long-term stockpiling of large PG volumes poses immense pressure to the ecological environment. To mitigate negative environmental impacts, the utilization of PG is imperative. Despite progress in PG utilization and 3D-printing technology, there is still a significant lack of understanding about the synergistic activation mechanisms in multi-solid-waste systems. In particular, the composition design, microstructure evolution, and structure–property relationships of 3D-printed PG-based composites are not well-studied, which limits their high-value engineering applications. Three-dimensional-printed phosphogypsum concrete (3DPPGC) is proposed here, promoting PG resource utilization by leveraging the expanding applications of 3D-printed concrete (3DPC). However, the strength of 3DPPGC needs to be enhanced to meet engineering requirements. This study designed the mix proportion of 3DPPGC and fabricated the corresponding test specimens. The optimal Cement Replacement Ratio (CRR) was determined through experimental testing, and the mechanism behind the strength enhancement of the 3DPPGC was elucidated. The results indicated that the 3DPPGC’s mechanical properties peaked at the 70% CRR. Compared with cast specimens, 3DPPGC exhibited a 1.52% increase in 28-day flexural strength in the y-direction, reaching 4.69 MPa. The early-age compressive strength, flexural strength, and later-age compressive strength of 3DPPGC were significantly enhanced when PG, blast-furnace slag (BS), fly ash (FA), and silica fume (SF) were used to partially replace cement. This study provides a theoretical and experimental basis for the large-scale, high-value application of PG in intelligent construction.
The construction sector undeniably has an impact on sustainability in its three dimensions: economic, social, and environmental. In this context, 3D concrete printing (3DCP) has emerged over the last decade as an attractive technology for transforming this sector. It enables the manufacture of construction elements while saving time, reducing waste, and eliminating the need for molds. However, assessments of the environmental performance of implementing this technology are limited, particularly under representative production conditions. This study evaluates the footprint family indicators, carbon footprint (CF), ecological footprint (EF), and water footprint (WF), of different mixtures of 1 m3 of 3D-printed concrete, with 1m of a high printed wall. These mixtures were made with a proportion of fresh solid aggregates; brick and concrete rubble (as demolition waste (CDW) materials) were used as partial replacements for cement. In addition, the environmental impact of using two printing technologies, gantry and robotic arm systems, is analyzed. The results show that materials are the main source of environmental impacts; the replacement of some of the cement reduces CF and EF by up to 20% and 19%, respectively, while preserving printability and buildability, as demonstrated by the stable fabrication of 1 m-high printed wall elements. However, moderate increases in WF were observed, which were associated with the electricity consumption of waste processing. These results confirm the potential for valorizing CDW in 3D printing mixtures. This environmental assessment under full-scale printing conditions supports sustainability-oriented decision-making in the construction industry.
7 3D printing (3DP) technology has gained more recognition in the construction industry in 8 recent years. This technique puts forward stringent requirements for the performance of 9 cementitious materials such as extrudability and buildability. However, due to the layer-by-10 layer printing process, 3D printing concrete (3DPC) shows characteristically different 11 properties from conventional mold-casting concrete. This study critically reviews the 12 mechanical behaviors and rheological properties of 3DPC, focusing on how important fibers, 13 aggregates, printing parameters and environmental conditions impact mechanical anisotropy, 14 and how well they could be described by different rheological models. The review found that 15 fibers and aggregates significantly affect the anisotropic behavior of 3DPC. In particular, the 16 interlayer bonding strength of 3DPC can be enhanced by introducing fibers and aggregates, but 17 it can be diminished by some solid waste aggregates. Environmental conditions are found to 18 have minor to some influences over the mechanical strength and anisotropy of 3DPC. In 19 addition, this review has evaluated the carbon footprint of different 3DPC recipes reported in 20 the literature and found that the sustainability of the 3DP construction technique is questionable 21 from the mix design perspective, while additional research is urgently needed on this aspect of 22 the technology.
The construction industry is undergoing a low-carbon and digital transformation. The application of recycled aggregates in 3D printed concrete has emerged accordingly, combining the advantages of solid waste recycling and automated manufacturing. However, the optimization of mix design and the prediction of mechanical properties for 3D printed recycled aggregate concrete (3DPRAC) face two main challenges, namely the micro defects inherent in recycled aggregates and the anisotropy caused by layered deposition. This study proposes a Gene Expression Programming (GEP)-based computational framework for the prediction of the splitting tensile strength (STS) of 3DPRAC. A dataset of 110 data points was generated, with layer height and loading direction as key printing parameters representing the anisotropic effect. GEP showed the best performance among models, with an R2 of 0.914 on the testing set. Furthermore, the GEP model provides explicit mathematical equations that delineate the contributions of individual input variables and reveal the nonlinear effects of fiber content and printing parameters on STS.
No abstract available
No abstract available
Three-dimensional-printed concrete (3DPC) is an additive manufacturing technology that forms 3D solids via layer-by-layer printing based on 3D model data, but it consumes large amounts of river sand (RS) and has poor frost resistance. To address these issues, this study used industrial waste electric arc furnace slag (EAFS) as an aggregate at 0–100% replacement ratios to test the workability, mechanical properties, frost resistance, and microstructures of 3DPC specimens. The results show that EAFS improves mortar flowability and extends the printing window, but full replacement increases slump and reduces constructability. The stress dispersion and dense packing effects of EAFS ensure excellent mechanical properties of specimens before and after freeze–thaw cycles. At an 80% EAFS replacement ratio, compressive and flexural strengths increase by 2.52%/13.8% and 10.6%/18.2%, respectively; after freeze–thaw cycles, the specimens exhibit the best frost resistance. The interfacial transition zone between EAFS and cement matrix is only 2 μm, with 1.8% lower porosity and 20.14% fewer harmful pores than the 100% RS specimen after freeze–thaw cycles. In conclusion, 80% EAFS replacement balances 3DPC performance and solid waste utilization, providing important references for EAFS’s safe application in 3DPC and its performance improvement mechanism.
No abstract available
The construction industry is at a pivotal point in its transition toward sustainable practices, driven by the need to reduce carbon emissions, resource consumption, and construction waste. 3D Concrete Printing (3DCP), an emerging digital fabrication technology, offers innovative solutions by enabling automated, layer-by-layer construction without the need for traditional formwork. This paper explores the role of 3D printed concrete in promoting sustainability across structural and environmental dimensions. It highlights the key benefits of 3DCP, including reduced material usage, minimized labor requirements, lower construction costs, and decreased environmental impact. The study also examines the integration of eco-friendly materials such as recycled aggregates, fly ash, geopolymers, and industrial byproducts into printable concrete mixtures, enhancing both sustainability and mechanical performance. In addition, the paper discusses technical challenges such as printability, structural integrity, and standardization, while presenting real-world applications and future directions. The findings demonstrate that 3DCP not only addresses many limitations of conventional construction methods but also represents a promising pathway toward green, efficient, and resilient built environments.
Solid waste generation from industrial production and construction activities has increased sharply in recent years. Improper disposal and abandonment of solid waste have led to significant resource loss and pose serious risks to soil, water, and air quality. As a result, incorporating solid waste into concrete production presents a promising strategy to reduce environmental pressure and promote sustainable development. This review investigates the feasibility and performance of various solid waste materials, such as fly ash, limestone powder, stone sludge, silica fume, waste glass, rubber particles, and recycled concrete sand, that are incorporated into 3D printed concrete (3DPC). These materials demonstrate the potential to enhance rheological behavior, mechanical strength, interfacial bonding, and dimensional stability of printable composites. Additionally, their incorporation reduces carbon emissions, diverts waste from landfills, and promotes resource circularity. The benefits and limitations of solid waste are critically evaluated, including printability challenges arising from particle morphology and water absorption. The review emphasizes the need for standardized cost-effectiveness analysis frameworks to quantify economic and environmental balance. Finally, this study highlights the importance of optimizing mix design, surface treatment techniques, and large-scale production strategies to enable widespread adoption of waste-based 3DPC in sustainable construction.
The growing demand for construction materials has intensified concerns regarding natural sand depletion and the accumulation of industrial waste. Among these wastes, oil-contaminated sand (OCS) generated from petroleum-related activities presents environmental challenges while also offering potential for beneficial reuse. Previous studies have reported that low OCS contents can enhance workability and improve mechanical properties, highlighting its potential as a sustainable construction material. This study investigates the feasibility of incorporating OCS as a partial replacement for natural sand in 3D concrete printing (3DCP). Three mixes containing 0%, 0.5%, and 1% OCS were evaluated in terms of flowability, setting behaviour, printability, rheological response, hydration behaviour, mechanical performance, anisotropic response, and microstructural characteristics. The results showed that OCS incorporation had only a limited influence on flowability, while both the initial and final setting times exhibited noticeable delays. The maximum printable layers reached from 19 for the control mixture to 22 and 26 layers for the 0.5% and 1% OCS mixes, respectively, accompanied by reduced settlement and structural deformation. Rheological analysis revealed higher static yield stress and structuration rates for the OCS-modified mixes, contributing to enhanced buildability and geometric stability. Hydration calorimetry showed comparable heat-flow behaviour between the control and OCS-modified mixes, suggesting only a limited influence of OCS on cement hydration kinetics. The incorporation of OCS improved the compressive strength of the printed mixes and reduced compressive anisotropy, while SEM observations revealed a denser and more homogeneous microstructure, particularly for the 0.5% OCS mix. Thus, the findings indicate that low-level incorporation of oil-contaminated sand is a viable strategy for improving the printability and performance of 3D-printed concrete, promoting the sustainable reuse of contaminated industrial waste.
Concrete 3D printing is a promising manufacturing technology for producing geometrically complex structures efficiently and cost-effectively, by eliminating the need for formwork, reducing labor, and minimizing waste. This method has the potential to lower carbon emissions and resource use. However, it does not mitigate the carbon emissions associated with cement production. Nonetheless, utilizing waste materials in concrete 3D printing may reduce concrete carbon emissions and support recycling. This study investigates the use of two industrial waste materials–fly ash (FA) and ground waste glass (GWG)–as partial substitutes for ordinary Portland Cement (PC) in 3D printable cement paste. The chemical composition, particle size distribution, rheological properties, and flexural strength of the mixtures were analyzed. Results show that specimens containing waste materials achieved strengths comparable to traditional cement mixtures. The flexural strength reduction in 3D printed versus cast specimens varied across mixtures: control (66% reduction), FA20 (35%), FA10-GWG10 (35%), GWG10 (32%), FA10 (11%), and GWG20 (4%). Hence, incorporating waste materials in concrete 3D printing is recommended, as it maintains mechanical integrity while promoting recycling and upcycling of industrial waste.
Constructions using 3D printing are supposed to have potential benefits in sustainability, increased construction productivity, resource efficiency. Having spectacular benefits in the construction era, it announces many demanding challenges in the selection of appropriate material. When agro-industrial wastes are incorporated into concrete materials, 3D printing may also have significant benefits for sustainability. This paper's primary goal is to examine the sustainability aspects considered in delivering 3D printed structured mainly from raw precursors and life cycle assessment perspective. Initial data bases collected from search engines like google scholar, science direct was further scrutinized for selecting the papers. This study reviews mix composition used for printing 3D assembly using waste material like Granulated blast furnace slag, fly ash, silica fume etc. Effectiveness of the waste materials contributing to mechanical and fresh characteristics are explored. Industrial waste mostly be dumped found to have significant impact printability properties also contributing to sustainability aspects. Nonetheless, life cycle assessment (LCA) results are used to show how using wastes in 3D printing concrete materials affects environment in comparison to using traditional materials. Study deals with three pillars of sustainability i.e., Economical, environmental and sustainability. Outcome of the paper will help the researcher to optimally choose the waste precursors to deliver quality 3D printed structure with sustainable perspective.
Three-dimensional concrete printing (3DCP) has emerged as a promising digital construction technology that reduces material waste, eliminates formwork, and enables complex geometries. However, its sustainability remains constrained by the extensive use of ordinary Portland cement (OPC) and natural aggregates. This review comprehensively evaluates waste utilization in extrusion-based 3D printed concrete, classifying applications into three pathways: cement replacement in OPC-based systems, waste-derived precursors in alkali-activated/geopolymer binders, and fine aggregate replacement. Industrial, agricultural, and marine wastes are assessed regarding their effects on rheology, printability, mechanical performance, interlayer bonding, and durability. The reviewed literature investigated waste incorporation levels reaching up to 50% for cement replacement, up to 70% for alkali-activated/geopolymer systems, and up to 100% for aggregate replacement, depending on the material type and application pathway. Industrial wastes, particularly fly ash, slag, silica fume, and metakaolin, represent the most mature materials and generally improve printability and long-term performance. Agricultural and marine wastes show promising sustainability potential but remain insufficiently investigated. Despite encouraging laboratory-scale results, challenges related to material variability, early-age performance, standardization, and scalability continue to limit practical implementation. The review identifies critical research gaps and outlines future directions for developing sustainable and field-ready 3DCP technologies.
A significant portion of Ukraine’s housing stock was destroyed as a result of the ongoing war. Today, the rapid construction of affordable housing is an urgent priority. Large volumes of construction and demolition waste have accumulated due to the destruction of infrastructure. This waste must be properly utilized. One of the innovative building technologies is 3D printing. In this study, an architectural-structural-technological system and an industrial technological complex were developed for the complete production cycle of building elements and structural components using 3D printing, incorporating construction waste for low-rise residential buildings. The requirements for production mobility and the use of distributed energy systems were considered. The problem of manufacturing floor slabs/elements using 3D printing has been solved. Also, attention was paid to the anisotropy of 3D-printed concrete, which must be considered in its design and strength control.
3D printing technology has the potential to reduce construction waste through its controlled manufacturing process and optimized material consumption, making it a promising sustainable construction approach with reduced environmental impact. However, current 3D printed structures often have a high carbon footprint due to the large amounts of fine-grained primary materials used in mortar composites. Most efforts to develop 3D printed structures are associated with concrete and Portland cement-based materials.This research presents an innovative approach for the reuse of gypsum to develop a material suitable for 3D printing, with the goal to industrialize the usage of waste gypsum in civil engineering. The objective of this study is to develop a sustainable gypsum-cement-pozzolanic (GCP) ternary binder composite, incorporating recycled industrial waste gypsum materials such as construction demolition waste gypsum (CDG), along with Portland cement and secondary pozzolanic materials. The GCP ternary composite combines the desired properties of gypsum, such as fast setting time, with those of Portland cement, which offers high final strength. The addition of a pozzolanic component is essential to ensure the chemical stability of this ternary system.As part of this study, ternary composites were designed and tested for their mechanical properties, durability, and suitability for 3D printing. Development and optimization of the ternary composite was carried out as a loop of procedures (Fig.1). Through these optimization procedures, a range of mixtures with necessary properties for 3D printing was found. To ensure sustainability and to assess the environmental impact of the mixtures, life cycle assessment (LCA) was performed.The LCA of GCP composites showed at least 1.5 times lower embodied energy and carbon dioxide emissions compared to Portland cement-based mortars. This is without considering avoided emissions from the end-of-life stage of gypsum waste, as well as higher technical properties that make GCP composites superior to regular cement composites. Considering these factors, GCP composites exhibit even lower emissions and are considered a viable alternative to Portland cement-based mortars.
Foam 3D printing in construction is a promising manufacturing approach that aims to reduce the amount of material, hazardous labor, and costs in producing lightweight and insulating building parts that can reduce the operational energy in buildings. Research using cement-free mineral foams derived from industrial waste showed great potential in previous studies that reduced the amount of concrete needed in composite structures. This article collates the latest developments in this line of work. It presents the material system with its principal components and the advanced robotic 3D printing setup with a climate-controlled fabrication chamber. Print path schemes and hybrid fabrication methods combining 3D printing and casting are evaluated. Furthermore, the article discusses the effect of different print path schemes on the thermal insulation and compressive strength performance of printed parts. A full-scale final prototype synthesizes these findings and demonstrates the fabrication of modular, lightweight, and insulating construction elements that can be assembled into monolithic wall structures. The advantages and challenges of this novel approach are elaborated on in the conclusions. Finally, the article presents future advancements required to leverage this research as a scalable construction method that can help address the biggest challenges in building low-carbon and energy-efficient structures.
No abstract available
No abstract available
No abstract available
No abstract available
This study investigates the alkali activation of waste glass powder (WGP) for developing 3D printable geopolymer concrete. The rheological, mechanical, and fire-resistance of 3D printed concrete were evaluated to determine the effect of WGP as a partial substitution for fly ash in geopolymers. Rheological results show that incorporation of WGP reduces the rheological properties of printable mixes. For instance, the apparent viscosity of mixes containing 50% WGP was reduced by 48% at low shear rate (0.1 s−1), and 46% at high shear rate (100 s−1). The corresponding reductions in the dynamic yield stress and plastic viscosity were 35% and 55%, respectively, indicating improved flowability and pumpability. However, compressive strength declined with increased WGP. The 28-day mold-cast strength decreased from 51.4 MPa to 35.6 MPa at 50% WGP. In contrast, the elevated temperature properties are enhanced with reduced strength loss for the WGP incorporated specimens, attributed to the sintering effect of WGP. .
Entirely construction and demolition waste (CDW)-based ambient-cured geopolymer mortars with rheological properties fitted for 3-dimensional additive manufacturing (3D-AM) were developed in an effort to combine the advantages of improved waste minimization, development of green materials and easy/fast/accurate materials production/processing. CDW-based hollow brick (HB), red clay brick (RCB), roof tile (RT), concrete rubble (C), and glass (G) were used for the development of geopolymer binders while C was used solely as fine aggregates. Mixtures were activated by different combinations of sodium hydroxide (NaOH), calcium hydroxide (Ca(OH) 2 ), and sodium silicate (Na 2 SiO 3 ) as the alkaline activators. Rheological assessments were made based on the empirical test methods including flow table, vane shear and modified mini-slump tests. Compressive strength measurements were also made. Finally, two representative mortar mixtures with low and high viscosity were printed via a laboratory-scale 3D printer and the rheological properties were correlated with printing behavior of geopolymer mortars. Overall, the study showed that entirely CDW-based geopolymer mortars without any chemical admixtures having suitable rheological properties for 3D-AM can be manufactured successfully. The empirical test methods utilized are adequate in determining the rheological properties of CDW-based geopolymer mortars suited for use in 3D-AM. The designed entirely CDW-based geopolymer mortars with adequate compressive strengths were shown to be capable of extrusion via 3D-AM free of any defects/discontinuity, capable of maintaining its initial shape under the effect of the weight of consecutive upper layers and fully matched with the designed printed structure.
No abstract available
No abstract available
Additive manufacturing using cement has evolved rapidly in recent decades, revolutionizing the construction industry. This technology automates building structures through computer-aided design, offering benefits such as reduced material waste, optimized material distribution, and the ability to use composite materials. This paper aims to examine the potential of using copper-slag-based geopolymers in 3D printing. Geopolymers have gained popularity as an alternative and more energy-efficient material to traditional building materials, while copper slag allows for reducing and managing mining industry waste. Moreover, samples formed in molds based on the same material were produced to evaluate the method of manufacturing on the mechanical properties of geopolymers. This paper presents an evaluation of the mechanical properties including the compressive, flexural, and shear strength of the layered material. It reveals promising results, with strength development mainly observed within the first 14 days. The results show that the compressive strength after 28 days of curing is 46.4 MP and 42.1 MPa for formed and printed samples, respectively. Furthermore, the average bending strength value ranges between 7.4 MPa and 7.8 MPa, regardless of the bending direction and forming method. The obtained results show that printed geopolymers demonstrate adequate layer bonding, confirming the profitability of the 3D printing technology. This research confirms that 3D printing technology enables the use of geopolymer binder materials based on copper slag, which opens the door to sustainable alternatives in construction practices.
The study investigates the potential of using Vietnam fly ash (FA) as a substitute for traditional Portland cement to reduce both the volume of landfilled waste and the carbon footprint of concrete mixtures, while maintaining adequate mechanical performance of the produced elements. Additionally, the incorporation of construction and demolition waste, recycled brick aggregate (BR), as a partial aggregate substitute was investigated to enhance the sustainability and resource efficiency of composite formulations. Five mixes, including a reference, were produced by casting and three-dimensional concrete printing (3DCP). Printability (flow table), water absorption (gravimetry and infrared thermography), and flexural/compressive behavior were assessed; printed specimens were tested parallel and perpendicular to the layer plane. Recycled additions reduced flow by 15–22%, yet all mixes remained printable. Printed specimens showed higher capillary uptake than cast ones. In flexure, modified mixtures composition exhibited 50% lower peak stress than the reference. Cast elements outperformed printed ones: the printed reference was 33% weaker than its cast counterpart, and other mixes were 10–15% lower. In compression, printed specimens loaded perpendicular to layers reached 6–7 MPa (35% below cast), whereas parallel loading yielded up to 3.5 MPa with larger scatter. The findings confirm the feasibility of utilizing secondary raw materials in 3DCP formulations to support resource efficiency and carbon footprint reduction in the construction industry.
To meet 2050 climate targets, the construction sector must reduce CO2 emissions and transition toward circular material flows. Recycled aggregates (RA) derived from construction and demolition waste (CDW) and industrial byproducts such as oil shale ash (OSA) show potential for use in concrete, although their application remains limited by standardisation and performance limitations, particularly in structural uses. This study aims to develop and evaluate low-strength, resource-efficient concrete mixtures with full replacement of natural aggregates (NA) by CDW-derived aggregates, and partial or full replacement of cement CEM II by OSA–metakaolin (MK) binder, targeting non-structural 3D-printing applications. Mechanical performance, printability, cradle-to-gate life cycle assessment, eco-intensity index, and transport-distance sensitivity for RA were assessed to quantify the trade-offs between structural performance and global warming potential (GWP) reduction. Replacing NA with RA reduced compressive strength by ~11–13% in cement-based mixes, while the aggregate type had a negligible effect in cement-free mixtures. In contrast, full cement replacement by OSA-MK binder nearly halved compressive strength. Despite the strength reductions associated with the use of waste-derived materials, RA-based cement-free 3D-printed specimens achieved ~30 MPa in compression and ~5 MPa in flexure. Replacing CEM II with OSA-MK and NA with RA lowered GWP by up to 48%, with trade-offs in the air-emission, toxicity, water and resource categories driven by the OSA supply chain. The cement-free RA mix achieved the lowest GWP and best eco-intensity, whereas the CEM II mix with RA offered the most balanced multi-impact profile. The results show that regionally available OSA and RA can enable eco-efficient, structurally adequate 3D-printed concrete for construction applications.
3D concrete printing (3DCP) is emerging as a transformative technology in the construction industry with a potential for lower manufacturing costs, enhanced design flexibility, and greater efficiency. Integrating construction and demolition waste (CDW) into 3DCP mixtures offers sustainability benefits but at the same time is associated with challenges of material variability and complex printing requirements. This study introduces a multi-objective Bayesian approach to concurrent optimization of mixture design and printing parameters targeting superior buildability with maximized CDW replacement. Following experimental trials driven by the multi-objective Bayesian optimization algorithm, we achieved 66 % improvement in terms of buildability at 97 % CDW replacement of natural sand. These mixture designs together with optimized printing parameters allowed 3DCP of six to ten layers without collapse. Mechanical tests combined with XRD and SEM characterization showed that higher CDW content with silica fume increased compressive strength, particularly in cast specimens. The tests performed in multiple directions further revealed anisotropy of compressive strength in 3D-printed samples with the highest strength in the Y-direction followed by that in the X and Z directions. Our findings demonstrate a viable path toward sustainable, high-performance concrete printing with substantial use of recycled materials facilitated by multiobjective Bayesian optimization approaches.
No abstract available
As alkali-activated materials represent a technical and environmental alternative for reducing cement consumption, it is necessary to enable their applications under the same conditions in which traditional Portland cement (OPC) is used. Supported by records of good mechanical performance, durability, and capacity to incorporate industrial waste, studies have investigated their use in additive manufacturing or 3D printing—a technology that is revolutionizing the construction sector by providing greater efficiency, design flexibility, and reduced consumption of material resources, although it still faces challenges related to process standardization and control of mixture properties. In this context, alkali-activated materials, which have the potential to incorporate industrial waste as precursors, can also absorb waste from the construction industry, such as construction and demolition waste. The use of industrial waste as precursors in alkali-activated matrices represents an innovative strategy to mitigate environmental impacts and promote a circular economy. This article presents a review of the main characteristics of certain wastes that modify rheological properties and printing parameters for additive manufacturing with alkali-activated matrices. It discusses the challenges and perspectives related to the use of three types of waste with such potential: red ceramic waste (RCW), mineral wool waste, and glass waste, considering how these materials can influence additive manufacturing after undergoing specific treatment processes. This discussion was conducted based on studies published between 2014 and 2025.
No abstract available
Three-dimensional concrete printing (3DCP), an innovative fabrication technique, has emerged as an environmentally friendly digital manufacturing process for using recycled waste materials in the construction industry. The aim of this review paper is to critically evaluate the current state of research on the use of recycled materials such as aggregates and powders in 3DCP, correlating the environmental, economic, and performance parameter effects. This review comprehensively evaluates the potential benefits of incorporating recycled waste materials in 3D printing by critically reviewing the existing peer-reviewed articles through a scientometric review. The resulting bibliometric analysis identified 73 relevant papers published between 2018 and 2024. Through the critical review, five main research categories were identified: recycled materials in 3DCP arising mainly from construction demolition in powder and aggregate forms, which investigates the types of recycled materials used, their extraction methods, morphology and physical and chemical properties. The morphology properties of the materials used displayed high irregularities in terms of shape and percentage of adhered mortar. In the second category, printability and performance, the buildability, rheological properties and the mechanical performance of 3DCP with recycled materials were investigated. Category 3 assessed the latest developments in terms of 3D-printed techniques, including Neural Networks, in predicting performance. Category 4 analysed the environmental and economic impact of 3DCP. The results indicated anisotropic behaviour for the printed samples influencing mechanical performance, with the parallel printing direction showing improved performance. The environmental performance findings indicated higher global warming potential when comparing 3DCP to cast-in situ methods. This impact was reduced by 2.47% when recycled aggregates and binder replacements other than cement were used (fly ash, ground slag, etc.). The photochemical pollution impact of 3DPC was found to be less than that of cast-in situ, 0.16 to 0.18 C2H4-eq. This environmental impact category was further reduced up to 0.10 C2H4-eq following 100% replacement. Lastly, category 5 explored some of the challenges and barriers for the implementation of 3DCP with recycled materials. The findings highlighted the main issues, namely inconsistency in material properties, which can lead to a lack of regulation in the industry.
No abstract available
This study investigates the feasibility of incorporating locally sourced construction and demolition waste (CDW) as fine aggregate replacements in 3D concrete printing (3DCP) mixes. Three mortar mixes were developed: a 100% natural sand reference mix, and two recycled mixes replacing natural sand with processed CDW at substitution levels of 25% and 50% by weight. Fresh-state properties, including initial setting time, flow diameter, and rotational rheometry, were evaluated to map the fresh matrix performance. The 28-day compressive strength was assessed to evaluate mechanical performance of the printable mixes. Results indicate that CDW mixes accelerated early structural build-up, peaking at a static yield stress of 2854.0 Pa for 50% replacement compared to 1235.5 Pa for the reference mix. Furthermore, the addition of CDW altered the plastic viscosity, which rose from a reference baseline of 1.8 Pa·s to 3.14 Pa·s at 25% replacement due to grain angularity, but dropped to 1.94 Pa·s at 50% replacement because of high superplasticizer lubrication. Testing on the layered specimens revealed a clear directional compressive strength hierarchy of x > z > y. This study shows the potential success of a practical blueprint for adopting local construction waste in structural 3DCP applications.
Rapid population growth and accelerating urbanization are intensifying the demand for construction materials, particularly concrete, which is predominantly produced with Portland cement and natural aggregates. This reliance imposes substantial environmental burdens through resource depletion and greenhouse gas emissions. Within the framework of sustainable construction, recycled aggregates and industrial by-products such as fly ash, slags, crushed glass, and other secondary raw materials have emerged as viable substitutes in concrete production. At the same time, three-dimensional concrete printing (3DCP) offers opportunities to optimize material use and minimize waste, yet it requires tailored mix designs with controlled rheological and mechanical performance. This review synthesizes current knowledge on the use of recycled construction and demolition waste, industrial by-products, and geopolymers in concrete mixtures for 3D printing applications. Particular attention is given to pozzolanic activity, particle size effects, mechanical strength, rheology, thermal conductivity, and fire resistance of recycled-based composites. The environmental assessment is considered through life-cycle analysis (LCA), emphasizing carbon footprint reduction strategies enabled by recycled constituents and low-clinker formulations. The analysis demonstrates that recycled-based 3D printable concretes can maintain or enhance structural performance while mix-level (cradle-to-gate, A1–A3) LCAs of printable mixes report CO2 reductions typically in the range of ~20–50% depending on clinker substitution and recycled constituents—with up to ~48% for fine recycled aggregates when accompanied by cement reduction and up to ~62% for mixes with recycled concrete powder, subject to preserved printability. This work highlights both opportunities and challenges, outlining pathways for advancing durable, energy-efficient, and environmentally responsible 3D-printed construction materials.
The increasing demand for sustainable construction materials has intensified research into geopolymers, with a particular focus on construction and demolition waste (CDW). CDWs present a promising opportunity for reducing the environmental impact of construction by serving as recycled precursors and aggregates in sustainable geopolymeric materials. Recent studies have confirmed the viability of CDW-based geopolymers, demonstrating numerous advantages, including enhanced mechanical durability, cost-efficiency, and overall sustainability characteristics compared to Ordinary Portland Cement (OPC)-based materials. Nevertheless, several challenges continue to impede their broader adoption in the construction industry. This review synthesizes the latest findings on the mechanical properties, durability, 3D printing applications, structural performance, and sustainability features of CDW-based geopolymers, highlighting critical factors such as the influence of CDW precursors and aggregates, mix design parameters, particle packing and shape characteristics. Literature underscores the necessity for enhanced design methodologies and standardized criteria to improve the practical application of CDW-based geopolymers, particularly in optimizing the mechanical performance, durability, and 3D printing formulations. Important limitations regarding the need for research in critical areas of CDW-geopolymers have been given.
This work addressed the problem of waste management, with an emphasis on the recycling of construction and demolition waste (CDW), through the application of 3D printing and injection molding technologies for the manufacture of eco-friendly paving stones. The results demonstrated the feasibility of producing functional materials that meet specific standards for properties such as water absorption and erosion resistance. However, the paving stones exhibited limitations in compressive strength, restricting their use to areas with low pedestrian traffic. The study concludes that the prototype is technically viable, economical, and environmentally friendly, reducing costs, utilizing waste, and mitigating the carbon footprint, thus demonstrating its potential to promote sustainable practices in the construction sector.
The large volume of industrial by-products and wastes from the construction, timber and paper industries has become a serious challenge worldwide. Recycling these industrial wastes as functional materials in the construction industry is an efficient approach for sustainable development. This study presents a pretreatment approach for recycling construction and demolition waste (CDW) and industrial side-streams (such as green liquor sludge, fiber waste, flotation sand and fly ash) in order to produce a geopolymer for the 3D printing of construction materials. A treatment approach was developed for screening the residues from CDW with a maximum size of 16 mm and for a combined line treatment for industrial side streams. The treatment processes utilized suitable and economical separation techniques for the recycling of waste materials. The crushing of the screened residues resulted in a homogeneous material size that facilitates the separation of mixed wastes and simplifies the classification of materials. The combined plant enabled the cost-effective treatment of various industrial wastes in a single process unit. The results show that the economic and environmental impact of the chosen techniques, in terms of their energy consumption, is highly dependent on the treatment line, separation technique and quantity of the individual waste that is processed. These recycled industrial wastes can be used as sustainable materials for the production of geopolymer concrete, contributing to the sustainability of the construction industry.
This study addresses environmental concerns related to construction and demolition waste (CDW), which constitutes 35–40% of global waste. It explores the potential use of recycled fine aggregates (RFA) from concrete demolition waste as a sustainable alternative to natural fine aggregates in 3D printed mortar (3DPM). By conducting a systematic literature review (SLR) and utilizing VOSviewer for bibliometric analysis, the research assesses the mechanical properties, flowability, extrudability, and buildability of RFAs in 3DPM. The analysis also highlights key trends in keywords and research distribution across different countries. The findings reveal that while RFAs in 3DPM slightly reduce compressive and flexural strengths compared to natural aggregates, they significantly contribute to environmental sustainability by reducing landfill waste and conserving natural resources. The study underscores the importance of further research to optimize RFA-based mixtures for wider application in 3D printing technologies. Recycled fine aggregates (RFAs) from construction waste are suitable for eco-friendly 3D printing applications. 3DPM with RFAs has reduced mechanical strength but remains viable for structural use. Optimizing RFA mix designs can enhance both sustainability and performance in 3D-printed concrete structures. Recycled fine aggregates (RFAs) from construction waste are suitable for eco-friendly 3D printing applications. 3DPM with RFAs has reduced mechanical strength but remains viable for structural use. Optimizing RFA mix designs can enhance both sustainability and performance in 3D-printed concrete structures.
Abstract This paper focuses on the evaluation of ambient-cured 100% construction and demolition waste (CDW)-based geopolymers in terms of rheological properties for 3-dimensional additive manufacturing (3D-AM). The CDW-based precursors used for geopolymer production were hollow brick (HB), red clay brick (RCB), roof tile (RT) and glass (G) activated by different combinations of sodium hydroxide (NaOH), calcium hydroxide (Ca(OH)2) and sodium silicate (Na2SiO3). Rheological properties were evaluated via empirical tests such as flow table, vane shear test, modified mini-slump test and compressive strength test for mechanical characterization. Based on these results, the extrudability performance of selected CDW-based geopolymer mixtures was analyzed with a ram extruder, and finally, a single mixture was selected to be used in laboratory-scale 3D-printing. The geopolymer mixture activated by 6.25 M NaOH and 10%-Ca(OH)2 exhibited the best performance in terms of rheology and compressive strength, and it was therefore selected for use in laboratory-scale 3D-printing. 3D-AM application at the laboratory scale showed that ambient-cured 100% CDW-based geopolymers can be successfully used for 3D-printing, with adequate rheological and mechanical properties and without any additional chemical admixtures, and that the empirical test methods used are effective in assessing the suitability of CDW-based geopolymers for 3D-AM applications. The outcomes of this work are believed to contribute to the current literature significantly, as they combine the advantages of green material development, waste upcycling, reduced raw materials and easy/fast/accurate producibility.
3D concrete printing technology offers an ideal solution for resilient infrastructure development in critical and emergency situations, but accessing required materials and energy can be challenging. This study focuses on an integrated renewable energy system with hydrogen storage to support a mobile and autonomous 3D printing system. The system is designed to meet off-grid energy needs, including material synthesis. Two local materials were analyzed: Construction and Demolition Waste (CDW)-based geopolymer concrete and directly printable local materials. Due to the energy-intensive process required for producing geopolymers, direct printing with local materials is more favorable. Under steady-state conditions, the 5.36 kW system can print 2.86 m3 of local material or 0.22 m3 of geopolymer concrete in 24 hours. The feasibility, production capacity, and overall performance of the system were analyzed under varying solar irradiance conditions. The environmental impact analysis identified CDW-based geopolymer materials as a hotspot, mainly due to the alkaline solution and energy required for mechanical processing. Using local materials for direct printing significantly reduced energy consumption and eliminated the need for an alkaline solution, reducing environmental impact by over 95%. The study demonstrates the potential energy and environmental benefits of using local materials, suggesting further exploration is warranted.
Concrete 3D printing faces challenges due to the global shortage of natural sand. In this context, construction and demolition waste, scallop shell waste, and recycled PET offer sustainable alternatives. This study develops and validates a concrete mix design methodology incorporating these recycled aggregates, using the Funk-Dinger model to optimize particle size distribution for 3D printing. A comprehensive experimental campaign was conducted to characterize the physical properties of source and blended aggregates, and to assess mixture printability through mortar flow tests, medium-scale 3D printing trials, and rotational rheometry. The results indicate that dense and loose packing fractions are governed not only by particle size distribution but also by aggregate morphology, as quantified by the Sphericity Deviation Index (SDI). Five formulations incorporating binary, ternary, and quaternary natural and recycled aggregate blends were successfully printed at a medium scale. Printable mixtures exhibited static yield strength values in the range of about 1500–2000 Pa, consistent with requirements for extrusion-based printing. In addition, flow-loss rates over 30 min ranged from approximately 3.2 to over 6 mm/min and were found to correlate with aggregate water absorption, granulometric parameters, and superplasticizer dosage. An exploratory, data-driven classification analysis further indicated that static yield strength and SDI are informative indicators for distinguishing printable from non-printable mixtures within the investigated material space. Overall, the findings highlight that, beyond controlling flowability and particle size distribution, accounting for aggregate shape and packing behavior is essential for the development of printable concretes incorporating recycled aggregates. The proposed framework provides a basis for future optimization and extension toward sustainable additive construction.
In this study, a procedure for mixture design was proposed with the aim of meeting the requirements of extrudability, buildability, and shape stability in 3D printable concrete. Optimum water/binder ratio, sand/binder ratio, binder type, utilization ratio, aggregate particle distribution and quantity, and type and utilization ratio of chemical admixtures were determined for 3D printable concrete in terms of print quality and shape stability criteria. A total of 32 different mixtures were produced. It was determined that mixtures produced using a binder content with approximately 40% fly ash, a w/b ratio of 0.35, and aggregates with Dmax of 1 mm exhibit acceptable characteristics. Investigations were also conducted into the thixotropic behavior, rheological characteristics, and mechanical properties of the mixes that were deemed acceptable. As a result, it was determined that the increase in the amount of fly ash usage positively affected the buildability of the printed layers. Additionally, the dynamic yield stress ranging from 114 to 204 Pa, viscosity ranging from 22 to 43 Pa.s, and structural build-up value ranges suitable for the production of 3D printable concrete mixtures were determined.
The construction of traditional underground utility tunnels faces prominent challenges, including high costs, long construction cycles, and limited workspace. Although 3D printing technology offers an effective solution to these issues, its practical application is largely constrained by key performance factors such as the printability, early strength, and interlayer bonding of concrete materials. This study aims to develop a 3D-printable concrete material specifically suited for the construction of underground utility tunnels. Through collaborative optimization of parameters such as the water–binder ratio, additives, and fiber content using single-factor and orthogonal tests, the optimal mix proportion was determined: a water–binder ratio of 0.30, a 10% dosage of rapid-hardening sulphoaluminate cement (R·SAC), a sand-to-binder ratio of 1.0, 20% mineral admixtures (15% fly ash + 5% silica fume), and a 1.0% volume fraction of polypropylene fibers. The results indicate that the fresh paste achieved a flowability of 192 mm, demonstrating excellent printability. Specimens printed using a sawtooth toolpath reached a 3-day compressive strength of 37.8 MPa, with 28-day compressive and flexural strengths increasing to 56.3 MPa and 7.8 MPa, respectively, and an interlayer bond strength of 3.5 MPa. Crucially, the compressive and flexural anisotropy coefficients were as low as 0.023 and 0.066, respectively, showing a preliminary exploratory trend superior to levels reported in some literature and suggesting the potential of printed components to improve structural performance consistency. This material system not only meets the requirements of 3D printing for early strength and workability but also, by introducing R·SAC to form a low-alkalinity binder system, provides a potential pathway for enhancing long-term durability in corrosive environments. This study offers a reliable theoretical and experimental basis for the application of 3D printing technology in underground engineering. Long-term durability will remain a primary focus of subsequent research.
The growing demand for sustainable binder systems in 3D-printed concrete (3DPC), together with the declining availability of fly ash (FA), has increased the need for alternative supplementary cementitious materials. This study investigates the feasibility of using basaltic rock dust (BRD) as a high-volume replacement of FA in 3DPC through a two-stage experimental programme involving mix optimisation followed by evaluation under printing conditions. Five mortar mixes incorporating BRD at FA replacement levels of 0%, 25%, 50%, 75%, and 100% by mass were first evaluated to identify the optimum replacement level within the investigated range, after which the optimum mix was comprehensively characterised in terms of its fresh properties, rheological behaviour, hydration characteristics, mechanical performance, anisotropy, and microstructure. The results showed that 75% FA replacement by BRD achieved the optimum overall performance among the investigated BRD-containing mixes, based on the combined consideration of high BRD utilisation, flowability, hydration behaviour, and compressive strength. Although its 28-day compressive strength under conventionally cast conditions remained slightly lower than that of the control mix, under printing conditions, the C75 mix increased the flow diameter from 165 mm to 176 mm and the maximum printable layers from 14 to 16 while reducing the shape retention spread diameter from 96 mm to 89 mm. Compared with the control mix, the BRD-incorporated mix also increased the compressive strength by 10.9% in the Y- direction and 22.9% in the Z-direction, respectively, while reducing the compressive anisotropy from 20.97% to 12.39%. Although the flexural strength decreased from 7.66 to 5.02 MPa in the Y-direction and from 7.29 to 5.19 MPa in the Z-direction, the directional dependence decreased from 4.83% to 3.34%. SEM observations revealed a more compact cementitious matrix with fewer visible large pores in C75 than in the control mix. These findings demonstrate that BRD has strong potential as a high-volume replacement for FA in 3D-printed concrete, reducing reliance on fly ash while achieving favourable printability, compressive performance, and structural uniformity.
Using high-volume cement in 3D printed concrete (3DPC) can lead to later crack formation. Accordingly, mineral admixtures can be used as cement replacements to mitigate this disadvantage. In this study, fly ash, slag, and a type of silica fume (with a high water consumption) are selected as supplementary materials in 3DPC under different substitution rates. A method for the printability evaluation of each test group in the orthogonal experiment is proposed based on a comprehensive analysis of the rheological behavior and mechanical performance of the test samples. The results indicate that a cement replacement ratio of 50% can be achieved in 3DPC while retaining its rheological behavior and mechanical performance. According to the actual printing test, the selected silica fume improves the buildability of 3DPC and can serve as an economical and effective cement substitute. The findings in this study also reveal the potential application of poor-quality mineral admixtures in 3DPC, which can increase economy and reduce CO2 emissions.
This study examines the rheological, mechanical, and microstructural characteristics of 3D-printed one-part geopolymer concrete (3DPOGPC) formulated from fly ash (FA) and ground granulated blast furnace slag, with metakaolin (MK) used as a partial or full replacement for FA. A high aggregate-to-binder (a/b) ratio of 1.9 was adopted from trial mixes for its optimum balance between extrudability and buildability, while reducing binder consumption. The static and dynamic yield stresses, and buildability increase with MK content. The compressive strength decreases with MK content, while the control mix (58.1 MPa) decreased by 34.9% at full FA replacement. However, printed specimens exhibited near-isotropic mechanical behavior. The elastic modulus followed similar trends, while test orientation influenced the direct tensile strength. XRD and SEM-EDX analyses confirmed the formation of C–A–S–H and C–(N)–A–S–H gels, contributing to matrix densification and strength improvement in FA-based samples. Overall, a high a/b ratio and MK can be effectively employed in 3DPOGPC.
No abstract available
Three-dimensional printing is an emerging technique that has received significant attention in the construction industry. This study presents an investigation into the printing and hardened properties of 3D-printed concrete (3DPC). Both fly ash (FA) and ground granulated blast furnace slag (GGBFS) were used to replace cement in different ratios (0%, 25%, and 50%) to produce 3DPC. Extrudability and buildability tests were performed to evaluate the effects of FA and GGBFS in various proportions on the printing properties of 3DPC. Additionally, the hardened properties of 3DPC were determined. Test results show that all mix designs meet the printing requirements of 3DPC. The specimens with a higher proportion of GGBFS exhibited higher unit weight and compressive and flexural strength, but lower water absorption and drying shrinkage. The compressive and flexural strength of 3DPC in the printing direction were the highest, outperforming those of the cast specimens at the age of 28 days. Our results indicate that FA and GGBFS can be used to replace 50% of the cement in 3DPC.
No abstract available
3D-printed concrete (3DPC) construction has gained global attention as an innovative and promising technique. However, the high cement content in 3DPC raises sustainability concerns, presenting a challenge for implementing sustainable processes. To address the issue, this research uses a low water-to-binder (w/b) ratio and incorporates silica fume (SF) and fly ash (FA) as partial cement replacements to reduce cement consumption and enhance sustainability. Three w/b ratios (0.33, 0.35, 0.37) and varying superplasticizer (SP) doses (0%, 0.25%, 0.5%, 0.75%, 1%) were tested, with 10% SF and 20% FA. The study investigated the physical, chemical, and morphological properties of the mix, alongside fresh, hardened, and durability properties, including workability, dry bulk density, compressive strength, dynamic modulus of elasticity, water absorption, and sulfate resistance. The results showed that a higher w/b ratio increased workability, with the w/b 0.37 mix exhibiting 50.71% higher workability than the w/b 0.33 and 45.09% higher than the w/b 0.35 for SP0 at 0 min. Besides, both a lower w/b ratio and increased SP content improved dry bulk density, compressive strength, and dynamic modulus of elasticity, with performance peaking at a 0.5% SP dosage in mix SP2. Additionally, reducing the w/b ratio decreased water absorption from 5.54% at 0.37 to 4.22% at 0.33 and lowered mass loss across all mixes; notably, the 0.33 mix with SP2 achieved the lowest mass loss (0.89%) and strength loss (3.12%). Despite these improvements, the use of SP increased production costs by 14.32%, while \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ {CO}_{2}$$\end{document} emissions rose only slightly by 0.89%.
No abstract available
This project investigates the feasibility and properties of 3D printed concrete using Portland Pozzolana Cement (PPC). The increasing demand for construction materials, particularly ordinary Portland cement (OPC), has led to a surge in its usage. Consequently, Portland Pozzolana Cement (PPC) has gained popularity as an alternative due to its advantageous properties. PPC, characterized by its enhanced durability and sustainability, has become a preferred choice in the construction industry, offering versatility and reliability in various construction applications. The main focus of the project is economical printing of concrete structures through 3D printing technology. With sustainability and cost-effectiveness as paramount considerations, the study delves into refining the mix proportions ideal for 3D printing applications. By harnessing the potential of Portland Pozzolana Cement (PPC) with a 35% fly ash content, the aim is to strike a balance between structural integrity, workability, and affordability. It examines various key properties essential for successful 3D printing, such as extrudability, printability, flowability, buildability, setting time and thixotropic open time. Furthermore, the project examines the strength of 3D printed concrete mixes. Through testing and studying these properties, the research aims to contribute to the advancement of eco-friendly and efficient construction practices by using 3D printing and innovative cementitious materials. The findings from this study provide valuable insights to enhance the efficiency of 3D printing and the strength of printed concrete structures, including beams, walls, and other structural elements. By implementing these ideas, potential advancements in construction methodologies could be realized, facilitating more robust and cost-effective building practices. This research aims to contribute to the ongoing evolution of 3D printing technology in construction, ultimately fostering innovation and sustainability in the built environment.
No abstract available
No abstract available
No abstract available
The additive manufacturing of concrete, also known as 3D-printed concrete, is produced layer by layer using a 3D printer. The three-dimensional printing of concrete offers several benefits compared to conventional concrete construction, such as reduced labor costs and wastage of materials. It can also be used to build complex structures with high precision and accuracy. However, optimizing the mix design of 3D-printed concrete is challenging, involving numerous factors and extensive hit-and-trail experimentation. This study addresses this issue by developing predictive models, such as the Gaussian Process Regression model, Decision Tree Regression model, Support Vector Machine model, and XGBoost Regression models. The input parameters were water (Kg/m3), cement (Kg/m3), silica fume (Kg/m3), fly ash (Kg/m3), coarse aggregate (Kg/m3 & mm for diameter), fine aggregate (Kg/m3 & mm for diameter), viscosity modifying agent (Kg/m3), fibers (Kg/m3), fiber properties (mm for diameter and MPa for strength), print speed (mm/sec), and nozzle area (mm2), while target properties were the flexural and tensile strength of concrete (MPa data from 25 literature studies were collected. The water/binder ratio used in the dataset ranged from 0.27 to 0.67. Different types of sands and fibers have been used, with fibers having a maximum length of 23 mm. Based upon the Coefficient of Determination (R2), Root Mean Square Error (RMSE), Mean Square Error (MSE), and Mean Absolute Error (MAE) for casted and printed concrete, the SVM model performed better than other models. All models’ cast and printed flexural strength values were also correlated. The model’s performance has also been checked on six different mix proportions from the dataset to show its accuracy. It is worth noting that the lack of ML-based predictive models for the flexural and tensile properties of 3D-printed concrete in the literature makes this study a novel innovation in the field. This model could reduce the computational and experimental effort required to formulate the mixed design of printed concrete.
No abstract available
Abstract Printable alkali-activated mixtures, which are homogeneous under pressure and achieve buildability in 3D concrete printing by extrusion-based layer deposition are developed. A baseline mixture of alkali-activated fly ash and slag is modified by using dry constituents such as micro-silica and clay. Carboxymethylcellulose (CMC) is used with the alkaline activating solution as a viscosity modifier. The roles of the different elements in influencing the yield stress, viscosity, and thixotropic buildup in the mixture are evaluated. The influence of yield stress and viscosity in influencing shape retention in printable mixtures is evaluated. Buildability is identified with the thixotropic buildup of elastic modulus and yield stress in the mixture. Phase separation in the mixture under pressure is influenced by the particle size distribution and the viscosity of the activating solution. Mixtures which do not exhibit phase separation under pressure have a narrower distribution of particle sizes, indicated by the Rosin-Rammler fit. Clay and CMC enhance the thixotropic buildup in the alkali-activated mixture and also contribute to achieving homogeneous flow under pressure by mitigating phase separation.
No abstract available
An embedded PZT sensor is developed for in situ monitoring of 3D-printed materials formed by extrusion-based layer deposition. The PZT sensor with a two-layer protection coating is embedded in the material during the layer deposition, and continuous measurements are obtained through the post-printing period. The PZT sensor is used to detect the physio-chemical changes in the alkali-activated fly ash-slag geopolymer with time. The effect of the added weight of each layer of print is sensitively reflected in the electrical impedance (EI) measurement obtained from the PZT sensor. The changes in EI measurements obtained from the embedded PZT sensor are compared with the measurements on the material related to the changes in the rheological behavior, reaction kinetics assessed using calorimetry, and setting behavior in the material. The build-up of the internal structure within the material, which allows buildability, is assessed from the conductance signature of the embedded PZT sensor. The changes produced by the chemical reactions within the binder, which bring about irreversible changes leading to the setting of the printed structure, are also sensitively detected in the EI measurements from the embedded PZT sensor. The amplitude of conductance is sensitive to the setting of the material. The frequency changes from the recorded EI signature reflect the continuous increase in the material stiffness with time.
Extrusion-based concrete 3D printing has huge potential to become a sustainable solution to the construction sector due to its advantages over the traditional mould based construction method. However, current 3D printable mixtures are not eco-friendly as they have significantly higher binder content compared to mould cast concrete. One of the solutions to this problem is the use of alkali-activated materials (AAMs). AAMs are made from industrial by-products being considered as alternatives for Portland cement. Though there is increasing attention towards AAM based concrete materials, their application in printed concrete is still limited due to the lack of a proper understanding of mixture design strategies. In this paper, pure and blended AAM based 3D printable mixtures were developed by using ground granulated blast-furnace slag (GGBS), stainless-steel slag (SSS) and copper slag (CS) as precursors. The GGBS based mixtures showed a good balance between flowability, open time and strength gain. The executed prints demonstrated a strength comparable with cast samples, highlighting an excellent interlayer bond strength.
Low-carbon and highly printable cementitious materials are crucial for the practical application of extrusion-based three-dimensional concrete printing (3DCP). This study develops and optimizes a one-part alkali-activated concrete suitable for 3D printing through an integrated experimental and evaluation approach. An orthogonal experimental design was employed to investigate the effects of precursor ratio (ground granulated blast-furnace slag, GGBFS, to fly ash, FA), water-to-binder ratio, activator dosage, and retarder content on fresh-state properties, rheological behavior, setting characteristics, and mechanical performance. The optimal mixture was determined using the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) multi-criteria decision method. The mixtures exhibited suitable rheology, with a yield stress of 90–141 Pa and a plastic viscosity of 3.5–7.2 Pa·s, a setting time of 40–96 min, and mechanical performance with compressive and flexural strengths of 29–71 MPa and 4.2–6.9 MPa, respectively. The optimal mixture provided a 95-min printing open time and an acceptable pumping pressure of 1.77 MPa, while full-scale tests confirmed stable extrusion and good print quality. Furthermore, within the defined cradle-to-gate, materials-stage boundary and the adopted inventory factors, the optimized alkali-activated mixture exhibited an embodied CO2 emission of 0.113 kg CO2/L, which is approximately 61% lower than that of the reference cement-based printable mixture. The proposed approach provides a systematic framework for designing low-carbon, high-performance one-part alkali-activated materials for extrusion-based 3D concrete printing applications.
Abstract 3D printing technology was recognized as a highly promising intelligent construction technique. Structures formed by the layer-by-layer deposition of strips exhibited characteristics of rapid forming and high automation. This study systematically investigated the rheological and buildability properties of cement-free alkali-activated materials as binders for 3D printing. Geopolymers are a subset of alkali-activated materials, while alkali-activated materials represent a broader class of binders that include slag-based systems and other compositions. Firstly, the rheological characteristics of alkali-activated materials were examined by varying the water-to-binder ratio, aggregate-to-binder ratio, and admixture content in the slurry. The results showed that the dynamic and static yield stresses, plastic viscosity, and thixotropic area of the slurry exhibited varying degrees of linear correlation with the added amounts of these mix design materials. Next, various designed mortar mixes were applied to the 3D printing process. Build height, open time, and strip width were all used as criteria to evaluate the printability of the slurry. Based on these three factors, the most suitable mortar mix for 3D printing was determined. Finally, a linear correlation between printing results and the static yield stress of the slurry was established based on rheological parameters. A strong linear relationship was demonstrated between the static yield stress of the slurry and the build height, open time, and strip width. Therefore, the printing outcomes of the designed alkali-activated materials could be predicted using the rheological parameters of the slurry. This correlation also allowed the design of slurry mixes suitable for construction according to build requirements. This study provided new insights and approaches for 3D printing technology using novel binder materials.
Efficient alkali-activated binder pastes of slag and fly ash-based aqueous nano-silica (FABANS) that provide enhanced strength are used for developing extrusion-based 3D printable concretes. The binder pastes of slag made with FABANS are not suitable for printing due to low yield stress and insufficient thixotropic buildup. Rheology control for enhancing the yield stress and thixotropic buildup is evaluated using bentonite clay and carboxymethyl cellulose (CMC). There is a synergistic enhancement in yield stress and thixotropic buildup provided by the combined use of bentonite and CMC that provides improved printability and buildability. Very rapid increase in yield stress with excess clay content in the presence of CMC, however, produces choking of flow and printability loss. Excess CMC results in a Maxwell-type behavior causing shape instability due to continuous relaxation under stress. The proportion of CMC and clay that provides the required thixotropic buildup for buildability is established. Printability and buildability of concrete mixture made with binder paste of FABANS with the proportion of rheology modifiers is demonstrated.
In response to the high environmental load and dependence on natural aggregates in traditional 3D-printed cement-based mortars, this study develops an alkali-activated 3D-printing mortar using industrial solid wastes such as ground granulated blast-furnace slag (GGBS), fly ash (FA), and steel slag sand as raw materials, aiming to promote the sustainable utilization of green building materials. The study systematically tests the working performance (flowability, shape retention, extrudability, buildability), mechanical properties (cube compressive strength and anisotropy), and combines X-ray diffraction and scanning electron microscopy analyses to reveal the hydration products and microstructural characteristics. The results indicate that the FA content and activator modulus significantly affect the mortar flowability, with the best shape retention and buildability at a flowability range of 170–220 mm. The cube compressive strength of the steel slag sand mortar increases with the GGBS content, reaching a maximum strength of 67.94 MPa at 28 days. Microstructural analysis shows the formation of C─(A)─S─H gel and the reinforcing effect at the interface of steel slag sand. This study provides a theoretical basis for applying 3D-printing materials entirely composed of industrial solid wastes in engineering, thereby advancing the synergistic combination of green building materials and sustainable construction practices.
3D concrete printing (3DCP) offers a transformative approach to industrialized construction and housing solutions. However, its reliance on high Portland cement (PC) mixes raises sustainability concerns. This study explores alkali-activated materials (AAM) as low-carbon alternatives, leveraging an industrial by-product (ground granulated blast furnace slag—GGBFS) to enhance environmental performance of 3DCP mortars. The novelty of this study lies in demonstrating that, despite equivalent activation parameters, one-part (“just-add-water”) and two-part AAM systems exhibit substantially different fresh-state, rheological, and printing behavior in extrusion-based 3DCP—an activation-method-dependent divergence that, to the best of the authors’ knowledge, has not been previously reported. Rheological behavior (dynamic yield stress, plastic viscosity, and structural build-up), flow table spread evolution, hydration kinetics (via isothermal calorimetry), and mechanical performance (cast and extruded specimens of selected mixes) were systematically evaluated. Results reveal that one-part mixes exhibit greater flowability when compared to two-part mixes (140–239 mm vs. 135–210 mm), inferior dynamic yield stress (35.94–93.61 Pa vs. 52.91–152.30 Pa), and slower structural build-up, while maintaining comparable compressive and flexural strengths as the equivalent two-part mortars. These findings demonstrate the potential viability of AAM for extrusion-based 3DCP and highlight the critical influence of activation method and water content on extrudability and performance.
No abstract available
To address the critical industry challenges of high carbon emissions and the inherent trade-off between printability and fast-setting performance of cement-based materials for 3D printed construction, this study developed a cement-free alkali activated composite tailored for 3D printing applications. It utilizes S95-grade ground granulated blast furnace slag (GGBS) and Grade I fly ash as the primary cementitious precursors, together with multi-grade quartz sand, polyvinyl alcohol (PVA) fibers, and tailored functional additives. Based on a printability evaluation system specifically developed for 3D printing materials, the effects of the mass replacement ratio of slag for fly ash on extrudability, buildability, and setting time were systematically investigated, and the corresponding hydration products and underlying micromechanism were characterized via X-ray diffraction (XRD). The results indicate that increasing the slag replacement ratio simultaneously enhances extrudability and buildability, and the initial setting time decreases linearly to within one hour at 100% slag replacement. XRD characterization reveals that the main hydration products are predominantly amorphous C-S-H and N-A-S-H gels, and the increased slag content significantly promotes the formation of these gel phases, which is the fundamental mechanism underlying the enhanced macroscopic printability.
Geopolymers, or other alkali-activated materials (AAMs), are a class of cementitious aluminosilicate binders with diverse and regulated material properties. They are synthesized by adding an alkaline solution, called an activator (often consisting of sodium hydroxide, NaOH, and sodium silicate, Na2SiO3, to aluminum- and silicon-rich raw materials. Examples of such materials include blast furnace slag, metakaolin or fly ash, which is a by-product of coal combustion. Expanded geopolymers are a promising alternative to other expanded materials, especially in terms of their use as refractory partitions withstanding temperatures well in excess of 500C, which puts them above other foamed materials such as polymer composites or foam systems. The ability to assess the setting time of foamed geopolymer mortar is an important factor influencing the economics of this process. In the case of alkaline-activated materials, special attention should also be paid to the effect of the activator and stabilizers on the setting rate of the geopolymer mortar. Existing methods of testing the hydration of cement mortar in the case of AAM seem to be insufficient, so the paper focuses on determining the setting time of foamed geopolymers in order to use them in the process of 3D printing of semi-finished products with appropriate mechanical and physical properties. The duration and intensity of each of the heat release processes identified during the first hours of AAM setting depends on the type of activator used and the type of material used. Activation of geopolymers with a NaOH-containing solution leads to reduced heat release within the first 24 hours of the reaction compared to silicate-activated binders, which is associated with a slower reaction process A method based on a thermistor probe based on a standard thermistor with a negative temperature coefficient was used to determine the setting time. Acknowledgement: Publication cost of this paper was covered with founds of the Polish National Agency for Academic Exchange, under the STARS EU program, grant number BNI-UE-2023-8, acronym STARS CUT-UA and the Polish National Centre for Research and Development in Poland, under the M-ERA.NET 3 program, grant number M-ERA.NET3/2021/115/3D-FOAM/2022, 3D-FOAM - Foamed Geopolymer Made by Additive Manufacturing for the Construction Technology Applications.
Abstract: Three-dimensional (3D) concrete printing (3DCP) is a transformative construction technique that offers the potential for greater efficiency, customization, and architectural flexibility. This technology is becoming increasingly necessary in the construction industry due to its ability to reduce labour costs, increase productivity, and minimize waste. The use of alkali-activated materials in 3DCP is gaining attention due to their superior mechanical properties and lower carbon footprint compared to traditional Portland cement. These materials, which include agro-industrial by-products like fly ash, slag and bagasse ash are activated by alkaline solutions to form a binder. The development of sustainable, alkali activated 3DCP materials is a critical step towards environmentally friendly construction practices. The primary focus of this research is to investigate the hardened properties of 3DCP materials, including compressive strength, flexural strength, split tensile strength, bond strength, and Poisson’s ratio. These properties are fundamental for predicting the performance of 3D printed structures under various loading conditions.
Based on the knowledge that exists today, it is generally accepted that there are basic parameters and characteristics to obtain effective mixtures for their use in 3D printing. Rheological behavior and setting time (initial and final) are those characteristics that determine workability, as well as the speed and nature of hardening of the molded pastes and, as a result, the final framework and the integrity of the resulted structure. Among the promising options for 3D printing, the literature often contains information on alkali-activated binders. In this work, an alkali-activated binding system based on electrometallurgical slag, as well as citrogypsum, a waste of the industrial production of citric acid, was studied. Some rheological characteristics of experimental binders were considered: the nature of the mixture flow under the action of torsional loads and their initial and final setting times. It was found that the joined use of both components in the experimental system “slag - water”: an alkaline activator and citrogypsum, promotes the transition of the character of the system from thixotropic to mixed: dilatant-thixotropic (for the Na2SiO3 activator) and dilatant (for the NaOH activator). It was found that the addition of alkaline activators and citrogypsum to the binding system separately in both cases helps to reduce the initial and final setting times from 18 and 22 hours to 1 hour and 1.5 hours. Also, experimental results have shown that the jointed action of both components: an alkaline activator and cytogypsum, has a synergistic effect on the setting time.
Abstract This study developed and verified a novel, alkali-free cementless material for 3D printing, formulated entirely from industrial by-products: circulating fluidized bed co-fired fly ash (CFA), blast furnace slag, fly ash, and reactive ultra-fine fly ash (RUFA). The research aimed to eliminate cement and hazardous liquid alkali activators by using the self-activated properties of CFA to activate the slag. The experimental program evaluated rheological properties for printability, compared the compressive strength of cast and 3D-printed specimens to assess anisotropy, and analyzed thermal conductivity and interlayer bonding using optical microscopy. Results showed the optimized cementless mixtures achieved stable fluidity and good extrudability, though with longer setting times than traditional alkali-activated materials (AAMs). While AAMs had superior compressive strength (over 60 MPa), their rapid hardening created weak interlayer bonding. Conversely, the cementless composites maintained continuous fusion and achieved lower thermal conductivity (minimum, 0.233 W/m K) due to an interstitial pore structure from RUFA. The study concluded that while AAMs were better suited for high-strength applications, the developed alkali-free composite offered a sustainable and energy-efficient solution for non-structural elements, striking a balance between buildability and thermal insulation. Its innovation lay in creating a self-activating, all-waste binder system that avoided corrosive chemicals while enabling tunable thermal properties in additive manufacturing.
Abstract The simple operation of one-part geopolymer has shown promising practicability for future in-situ construction similar to ordinary Portland cement. Intending to meet the demand of various industrial applications such as 3D printing, this study aims to tailor the early-age properties of one-part fly ash/ground granulated blast-furnace slag (FA/GGBS) geopolymer through the utilization of hybrid activators, such as anhydrous sodium metasilicate (Na2SiO3), sodium carbonate (Na2CO3), and sodium aluminate (NaAlO2). The reaction kinetics and chemistries of such alkali activators are expounded to understand the working principles and their contribution to the performance improvement of one-part geopolymer. The experimental results indicated that Na2SiO3-activated one-part geopolymer released high reaction heat and achieved a faster setting. Such shortcomings could be improved by partial replacement of Na2SiO3 with Na2CO3 in a solid form. Besides, the incorporation of slight NaAlO2 decreased the self-flow of geopolymer paste, whereas the slump-flow properties remained unchanged.
The activity of gold tailings was activated by alkali activation method. Cement and gold tailings were used as cementitious materials to prepare 3D printing concrete. The mechanical properties and rheological characteristics of the slurry were measured to evaluate its performance during 3D printing. The results showed that when the content of gold tailings was approximately 1:1 with the amount of cement, the 28-day strength reached 31.9MPa, and the concrete had the best performance during 3D printing. The lateral deflection of the cylindrical components printed with gold tailings concrete was more than 50% lower than that of traditional concrete, the structural integrity was higher, and the printing open time was within a reasonable range.
Additive manufacturing of geopolymer-based materials requires a careful balance between flowability, structural build-up, and interlayer cohesion. In this study, sustainable geopolymer binders derived from untreated ceramic sludge were developed and evaluated for extrusion-based 3D printing under both ambient and sub-ambient (0–5 °C) conditions. Bentonite and citric acid were introduced as functional additives to tailor fresh-state rheological behaviour and process stability. Rheological performance was characterised using steady-shear measurements and interpreted through Bingham and Herschel–Bulkley models, with parameters extracted from the downward branch of the hysteresis loop to represent the post-shear structural state relevant to extrusion–deposition processes. At room temperature, the formulations exhibited well-defined yield-stress behaviour and controlled shear-thinning response, enabling stable filament formation. Under cold conditions, a reduction in apparent viscosity was observed, attributed to delayed geopolymerisation kinetics and limited early-stage network connectivity. Despite these effects, selected compositions maintained sufficient green-state cohesion to ensure layer stability. By correlating rheological descriptors with extrusion trials and microstructural observations, a process window for printable waste-derived geopolymer inks is proposed. The results highlight the feasibility of temperature-sensitive additive manufacturing using unprocessed ceramic waste, contributing to the development of sustainable and scalable geopolymer-based 3D printing systems.
The successful application of extrusion-based 3D-printed geopolymer mortars largely depends on precursor chemistry, activator composition, mixture proportions, and fresh-state behavior, which is highly sensitive to time-dependent structural build-up. This review examines the relationships among mix design, geopolymerization chemistry, rheological properties, and printability requirements for 3D-printed geopolymer mortars. Particular emphasis is placed on the effects of precursor type, alkaline activator characteristics, liquid-to-solid ratio, additives, and fibers on flowability, yield stress, viscosity, extrudability, buildability, shape retention, and interlayer bonding. The review further discusses how geopolymerization kinetics influence the evolution of fresh-state properties, the printable time window, and the transition from extrusion to structural stability. In addition, early-age performance is evaluated in terms of setting behavior, green strength development, and layer-interface integrity. Current challenges, including the lack of standardized test methods, limited comparability among published studies, and the complex coupling between material design and process parameters, are also highlighted. Finally, the review identifies key research gaps and proposes future directions for developing robust, printable, and sustainable geopolymer mortar systems for additive manufacturing in construction.
Recent years have witnessed a significant growth in the research and development of additive manufacturing methods involving concrete and cementitious materials, with technologies like three-dimensional (3D) printing becoming more widely used in the construction industry. Construction has the possibility to be revolutionized, not only in the context of cost savings but also in the context of increased sustainability and functionality. 3D printing of concrete is a cutting-edge technology that has the potential to speed up construction, reduce labor costs, give architects more creative freedom, improve precision, obviate requirements for formwork, and result in less construction wastes. In addition, 3D printing can be a long-term solution for both economy and environment. Even though 3D printing in concrete has made tremendous strides recently, developing an effective 3D-printable material that decreases material usage and enhances performance is critical for carbon dioxide reduction. Robust geopolymer formulations for 3D printing concrete technology in current construction applications have emerged as the subject of much research among scientists to find novel ways to circumvent this constraint. This study intends to highlight the current state of the art in developing 3D-Printed Geopolymer Concrete (3DPGC) with a comprehensive review related to the material composition, mix design, and mixing regimes on rheology of 3DPGC. The rheology of 3DPGC in terms of printability and buildability is discussed. The mixing regimes employed for the preparation of one-part and two-part 3DPGC are tabulated and commented on. Lastly, the research gaps are identified and summarized, and several research directions are also provided for future investigations to expedite the ubiquitous use of 3DPGC in versatile construction applications.
Highlights What are the main findings? 3D-printed permanent formwork enables efficient printed-cast composite construction. Rheology and buildability govern printing stability and dimensional accuracy. Printed-cast interface quality is critical to composite structural performance. Printed formwork can enhance strength, ductility, and confinement of structural members. Geopolymer systems represent an emerging low-carbon option, but direct permanent formwork evidence remains very limited. What are the implications of the main findings? Permanent formwork can reduce formwork use, labor demand, and construction waste. Interface engineering is essential for reliable composite structural action. Mix design must balance printability, mechanical performance, and durability. Standardized design and testing methods are needed for structural implementation. Long-term durability and full-scale validation remain key research priorities. Abstract Three-dimensional concrete printing (3DCP) has emerged as a promising technology for developing stay-in-place cementitious and geopolymer permanent formwork systems. This review critically synthesizes current knowledge on printable materials, printability requirements, structural performance, interfacial bonding, durability, sustainability, and microstructural characteristics. Existing studies demonstrate that 3D-printed permanent formworks can contribute structurally by enhancing the axial, eccentric, and flexural performance of composite members through confinement, composite action, and effective load transfer between the printed shell and cast concrete core. Interfacial bonding is identified as a key factor governing structural performance, with layer height, interface geometry, surface roughness, and casting interval significantly affecting tensile and shear bond strengths. Microstructural studies further highlight the roles of pore characteristics, hydration development, and mechanical interlocking in interface formation. Although cementitious systems dominate current research, geopolymer permanent formworks remain comparatively underexplored despite their sustainability potential. Moreover, durability studies, life-cycle assessments, and direct comparisons between cementitious and geopolymer systems remain scarce. This review identifies key research gaps and outlines future directions toward performance-based design methodologies and the broader structural implementation of 3D-printed permanent formwork systems.
Abstract The traditional cement production wastes a large amount of natural resources and energy, and causes environmental pollution, which cannot meet the green and sustainable development needs of modern building materials. Geopolymer is an environmentally friendly materials that can utilize industrial solid wastes and have low environmental load and energy consumption, which is expected to become a substitute for OPC. However, geopolymers also have shortcomings in some properties that need to be improved. This paper reviews the recent research progress on the performance improvement, potential new applicationw and sustainability assessment of geopolymer materials. Discussion from this paper showed that the properties of geopolymer materials, including rheology, hardening properties, toughness, etc., can be significantly improved by some methods such as chemical additives, mineral admixtures, nanoparticles, fibers, etc. Furthermore, this paper proves that geopolymers have great application potential as porous thermal insulation materials and 3D printing building materials, and points out some performance optimization methods for geopolymer-based porous materials and 3D printing materials. In this work, it was also concluded that geopolymer shows significant advantages over OPC in sustainable analysis index such as E-energy and E-CO2 (Energy and CO2 emission) based on LCA method. Finally, a few potential opportunities and development directions have been suggested for future research on geopolymer materials.
To optimize the shape stability of 3D-printed white calcium sulfoaluminate (WCSA) cement composites, oyster shell powder (OSP) and cuttlebone powder (CBP) were introduced as white admixtures to regulate rheological properties and printability. The setting behavior, rheological properties, and shape stability of the WCSA cement composites were evaluated by Vicat setting-time tests, rotational rheological measurements, three-stage thixotropic recovery tests, and structural deformation measurements, together with mechanical strength tests, XRD, and SEM analyses. The results showed that the incorporation of OSP and CBP shortened the setting time of WCSA cement composites. The initial and final setting times decreased from 41 min and 67 min to 17 min and 30 min in the WCSA cement composites with OSP, and from 42 min and 66 min to 20 min and 33 min in the WCSA cement composites with CBP, which improved printing operability. As the OSP and CBP content increases from 0% to 24%, the dynamic yield stress of WCSA cement composites increased from 48.83 Pa to 530.59 Pa and 60.30 Pa to 1085.80 Pa, respectively. The thixotropic recovery degree of WCSA cement composites increased from 57.89% to 86.46%, and 56.60% to 92.14%, respectively. As the OSP and CBP contents increase from 0% to 24%, the structural deformation decreased from 12.39% to 6.91% and 13.29% to 5.12% respectively, which improved buildability of the printed structures. In addition, although OSP and CBP reduced the mechanical strength of WCSA cement composites compared with the control group, the flexural and compressive strengths gradually recovered as the contents increased from 6% to 24% due to the enhanced filling effect and improved particle packing. This study provides a reference for the application of marine calcareous solid wastes in sustainable 3D-printed cementitious materials.
This study develops and evaluates a 3D-printable, waste-based alkali-activated mortar designed for improved thermal insulation in building applications. Brick masonry waste is utilized as both binder and aggregate to address sustainability challenges associated with ordinary Portland cement and scarce industrial by-products. A series of mix formulations with increasing recycled brick waste content (50–80% of total solids by weight) were produced and tested for fresh properties, mechanical strength, and thermal conductivity. The optimal mix (BA0.7) balanced extrudability, buildability, and strength with a low thermal conductivity, and was successfully used in 3D printing experiments. Numerical simulations were then conducted on five wall geometries with varying internal void configurations using the measured material properties. The finite element thermal analysis was first validated against literature data, showing close agreement in thermal transmittance (U-value). Results demonstrate that increasing the wall’s void ratio significantly reduces U-values, indicating better insulation, yet the geometry and distribution of load-transfer “contact points” between wall layers strongly influence heat flow. The best-performing 3D-printed wall design achieved a U-value of ~4.1 W/m²K, a 75% reduction compared to a solid wall of the same thickness. A cradle-to-gate life-cycle assessment (LCA) revealed that, after optimization of the internal pattern, the 3D-printed wall achieved an approximately 70–80% reduction in embodied impacts relative to the solid baseline. These findings highlight the potential of combining recycled-waste geopolymer materials with optimized 3D-printed wall designs to create lightweight, thermally efficient building envelopes. The novel material and wall configurations proposed can reduce building energy consumption and carbon footprint, supporting a transition toward sustainable construction. Future research should explore durability, multi-functional optimization (e.g. acoustic and structural performance), and the integration of passive insulation strategies to further enhance these 3D-printed systems.
Three-dimensional Cementitious materials Printing (3DCP) is a cutting-edge technology for the construction industry. Three-dimensional printed buildings have shown that a well-developed automated technology can foster valuable benefits, such as a freeform architectural design without formworks and reduced human intervention. However, scalability, commercialization and sustainability of the 3DPC technology remain critical issues. The current work presents the ecological fragility, challenges and opportunities inherent in decreasing the 3DCP environmental footprint at a material level (cementitious materials and aggregates). The very demanding performance of printable mixtures, namely in a fresh state, requires high dosages of cement and supplementary cementitious materials (SCM). Besides the heavy carbon footprint of cement production, the standard SCM availability might be an issue, especially in the longer term. One exciting option to decrease the embodied CO2 of 3DCP is, for example, to incorporate alternative and locally available SCM as partial cement replacements. Those alternative SCM can be wastes or by-products from industries or agriculture, with no added value. Moreover, the partial replacement of natural aggregate can also bring advantages for natural resource preservation. This work has highlighted the enormous potential of 3DCP to contribute to reducing the dependence on Portland cement and to manage the current colossal wastes and by-products with no added value, shifting to a Circular Economy. Though LCA analysis, mixture design revealed a critical parameter in the environmental impact of 3DCP elements or buildings. Even though cement significantly affects the LCA of 3DCP, it is crucial to achieving adequate fresh properties and rheology. From the literature survey, mixtures formulated with alternative SCM (wastes or by-products) are still restricted to rice husk ash, Municipal Solid Waste ashes and recycled powder from construction and demolition wastes. Natural aggregate replacement research has been focused on recycled fine sand, mine tailing, copper tailing, iron tailing, ornamental stone waste, recycled glass, crumb rubber, rubber powder and granules, recycled PET bottles and steel slag. However, flowability loss and mechanical strength decrease are still critical. Research efforts are needed to find low-carbon cement replacements and mix-design optimization, leading to a more sustainable and circular 3DCP while ensuring the final product performance.
This study examines the mechanical properties and microstructural characteristics of the interfacial transition zone in 3D-printed recycled concrete incorporating cockle shell aggregate and polypropylene (PP) waste fishing net. The shell aggregate and waste fishing net underwent the requisite pre-treatment, and a concrete mix suitable for 3D printing was selected with a focus on recycling marine waste. The specimens were subjected to compressive and flexural strength tests in accordance with KS L ISO 679, while their microstructure was analyzed using scanning electron microscope (SEM) images obtained in backscattered electron (BSE) mode. The SEM images were segmented using a histogram-and morphology-based phase segmentation method, as well as pixel value differences in regions exhibiting an interfacial transition zone, to analyze microstructural characteristics. The mechanical properties were evaluated by measuring the compressive and flexural strength of specimens with varying PP fiber contents, specifically 0.0%, 0.5%, and 1.0 vol.%. The results demonstrated that the specimen containing 0.5 vol.% PP fiber exhibited the highest compressive and flexural strength, which was attributed to the fiber bridging effect. SEM image analysis revealed that larger-diameter pores were observed at the interface between the shell fine aggregates and binder compared to those in the fine aggregate case, whereas relatively smaller pores formed around the PP fibers. A correlation was thus established between the microstructural analysis results and mechanical performance.
No abstract available
No abstract available
Ferronickel slag and ground granulated blast-furnace slag (GGBFS) are solid waste by-products from the metallurgical industry. When incorporated into concrete, they help promote resource utilization, reduce hydration heat, and lower both solid waste emissions and the carbon footprint. To facilitate the application of ferronickel slag–GGBFS concrete in 3D printing, this study examines how aggregate size and nozzle diameter affect its performance. The investigation involves in situ printing, rheological characterization, mechanical testing, and scanning electron microscopy (SEM) analysis. Results indicate that excessively large average aggregate size negatively impacts the smooth extrusion of concrete strips, resulting in a cross-sectional width that exceeds the preset dimension. Excessively small average aggregate size results in insufficient yield stress, leading to a narrow cross-section of the extruded strip that fails to meet printing specifications. The extrusion performance is closely related to both the average aggregate size and nozzle diameter, which can significantly influence the normal extrusion stability and print quality of 3D printed concrete strips. The thixotropic performance improves with an increase in the aggregate size. Both compressive and flexural strengths improve with increasing aggregate size but decrease with an increase in the printing nozzle size. Anisotropy in mechanical behavior decreases progressively as both parameters mentioned increase. By examining the cracks and pores at the interlayer interface, this study elucidates the influence mechanism of aggregate size as well as printing nozzle parameters on the mechanical properties of 3D printed ferronickel slag–GGBFS concrete. This study also recommends the following ranges. When the maximum aggregate size exceeds 50% of the nozzle diameter, smooth extrusion is not achievable. If it falls between 30% and 50%, extrusion is possible but shaping remains unstable. When it is below 30%, both stable extrusion and good shaping can be achieved.
The study focuses on the development of cementitious composites using 3D printing and plastic waste as a sustainable aggregate substitute. This study involves experimenting with various percentages of plastic waste as a partial substitute for ground granulated blast furnace slag (GGBFS) in a control mix. The study examines the anisotropy of the 3D printing process, comparing it with properties of mold-cast samples. In addition, it assesses the fire resistance and mechanical properties of samples at elevated temperatures (100 °C, 300 °C, and 600 °C). Key mechanical properties, including 28-day compressive stress and flexural strength, are determined through experimental testing using a standard compression test and three-point bending test. The study also considers the modulus of elasticity (MOE) in compressive tests to evaluate a sample’s ability to deform elastically and the flexural toughness index to assess energy absorption and crack resistance of flexural samples. Following the experimental testing, the study’s key findings suggest that significant mass loss occurred at 300 °C and above, with plastic samples demonstrating increased mass loss at 600 °C. At 600 °C, plastic degradation led to the formation of voids and cracks within samples due to heightened internal pressure. Anisotropy was evident in 3D-printed samples, with loads parallel to the layer direction resulting in greater compressive strength and MOE. Furthermore, layer direction parallel to the longitudinal axis of flexural samples yielded higher flexural strength and flexural toughness. Mold-cast samples displayed superior compressive strength and stiffer behavior, with higher MOE compared to 3D-printed samples. However, 3D-printed plastic samples exhibited superior flexural strength compared to mold-cast samples, attributed to the alignment of plastic within the samples. The study also observed a reduction in compressive strength with the addition of plastic, explained by the poor bonding of plastic with cement due to its hydrophobic nature. Despite this, flexural strength generally improved with plastic addition, except at 600 °C, where plastic samples showed significant degradation in both compressive and flexural strength due to plastic degradation within the samples.
Abstract Extrusion-based 3D concrete printing (3DCP) is emerging as a viable construction method due to its potential to enhance automation, reduce material waste and enable low-carbon construction solutions. However, its practical implementation remains constrained by the need for precise control of fresh-state rheology and early-age structural stability. This study investigates the combined influence of three nanoclays, attapulgite (ATT), bentonite (BEN) and sepiolite (SEP), together with a polycarboxylate ether superplasticizer (SP) on the rheological and mechanical behaviour of sustainable mortars developed for 3DCP-related applications. The binder system incorporates 50 % ground granulated blast furnace slag (GGBS) and 3 % silica fume (SF) to reduce embodied carbon while maintaining performance. A controlled shear-rate protocol was used to quantify static yield stress, dynamic yield stress, thixotropy and plastic viscosity, supported by slump-flow and compressive and flexural strength testing at 7 and 28 days. The results show that all nanoclays significantly enhance structuration and thixotropy, with SEP producing the strongest increase in static yield stress and structural rebuilding. ATT and BEN also improved rheological stability, although with lower intensity. SP dosage strongly governed flow behaviour, with 1 % providing the most favourable balance between flowability and shape stability. Nanoclay-modified mixes exhibited reduced slump flow and increased plastic viscosity relative to the reference. SEP yielded the highest 28-day compressive strength, while flexural strength decreased slightly across all nanoclays. The findings demonstrate that targeted combinations of nanoclay and SP can effectively tailor the rheology of low-carbon mortars, indicating their potential suitability for 3D concrete printing.
No abstract available
3D concrete printing (3D CP) is an advanced form of additive manufacturing (AM), that allows for the creation of complex geometrical structures using concrete. This technology has the potential to reduce construction time and labour costs while minimizing material waste. However, there are also challenges related to material properties, structural integrity, and standardization of construction practices. The primary challenge in developing 3D printable cementitious materials lies in engineering specific fresh properties that enable extrusion-based printing. Unlike cast concrete, where formwork provides dimensional stability during the printing process, the absence of formwork in 3D printing necessitates fresh mixtures with low-slump and high-thixotropy to be suitable for concrete 3D printing. Additionally, the orthotropic nature of the resulting 3D printed object due to the extrusion process impacts its mechanical properties. Therefore, this research aims to study the effect of water content and loading directions on 3D printed concrete. A pre-mix material from Sika was used in this study. Three mixes were prepared by using three different water to dry material (w/d) ratios, 0.140 l/kg, 0.145 l/kg and 0.150 l/kg. The experiments focused on analysing flowability, green strength, mechanical properties (compressive strength, flexural strength, and modulus of elasticity), water absorption, porosity, and chemical transformations at high temperatures through thermoanalytical measurement. The results showed that the mixture containing 0.145 l/kg (w/d) exhibited satisfactory 3D printability, optimal mechanical performance, lower porosities compared with mixtures 0.140 and 0.150, and same total porosity compared with cast specimen.
3D concrete printing (3DCP) technology holds significant potential to revolutionise traditional concrete production methods, offering designers and architects greater flexibility in creating intricate and innovative structures. Beyond structural applications, 3D printed concrete products encompass decorative elements, customised design solutions, and even artistic installations. The 3DCP process is highly automated, often integrating building information modelling (BIM) systems, minimising the need for manual labour and generating minimal material waste. 3DCP is regarded as one of the most advanced and efficient methods for fabricating concrete components in the future. This paper examines 3DCP technology and equipment, focusing on the selection of binder types, aggregates, and chemical admixtures, suitable for printable concrete mixes. Particular attention is given to the consistency and workability of 3DCP mixtures. Furthermore, the study evaluates the influence of 3D printing parameters on the mechanical properties of hardened concrete. The insights presented in this review contribute to a deeper understanding of 3D concrete printing technologies, equipment, and materials, benefiting researchers, structural engineers, and designers in the pursuit of enhanced durability and performance of 3D printed concrete structures.