3D打印混凝土开裂优化的方法
收缩与早龄期开裂机理:塑性收缩、毛细压力与开裂风险量化
合并三组中所有以“为什么开裂”为核心的机理与测量文献:涵盖塑性/干燥/自收缩变形机理与环境影响、毛细压力发育建模、大型打印构件与受限收缩开裂行为,以及激光/非接触数字图像相关等塑性收缩开裂量化测试方法与开裂风险模型。共同点为阐明开裂驱动力并提供可比较的测量—风险评价链条,是全部优化方法的基础。
- Shrinkage behavior of cementitious 3D printing materials: Effect of temperature and relative humidity(Mohsen Rezaei Shahmirzadi, A. Gholampour, A. Kashani, T. Ngo, 2021, Cement & Concrete Composites)
- Mitigating early age cracking in 3D printed concrete using fibres, superabsorbent polymers, shrinkage reducing admixtures, B-CSA cement and curing measures(G. M. Moelich, P. J. Kruger, R. Combrinck, 2022, Cement and Concrete Research)
- Experimental testing method for plastic shrinkage crack risk assessment(Laura Esposito, Martina Palomba, Amina Dacić, E. Wagner, 2026, ce/papers)
- Methods for measuring plastic shrinkage and related cracking of 3D-printed concrete(S. Markin, V. Mechtcherine, 2023, Journal of Physics, Conference Series)
- A plastic shrinkage cracking risk model for 3D printed concrete exposed to different environments(G. M. Moelich, P. J. Kruger, R. Combrinck, 2022, Cement & Concrete Composites)
- A review of shrinkage and restrained shrinkage cracking in 3D concrete printing(Heinrich Els, G. V. Van Zijl, W. D. De Villiers, 2025, Journal of Building Engineering)
- Plastic shrinkage and cracking of 3D printed mortar with recycled sand(Hang-Hua Zhang, J. Xiao, 2021, Construction and Building Materials)
- Cracking behaviour in 3D concrete printed fibre-reinforced cementitious composites: A Review(M. R. Delavar, F. Aslani, Tim Sercombe, 2025, Journal of Building Engineering)
- Modelling the development of capillary pressure in freshly 3D-printed concrete elements(Sadegh Ghourchian, M. Butler, M. Krüger, V. Mechtcherine, 2021, Cement and Concrete Research)
- Advanced measurement techniques for plastic shrinkage and cracking in 3D-printed concrete utilising distributed optical fiber sensor(Hang-Hua Zhang, Lu-Cen Hao, Shenmin Zhang, J. Xiao, C. Poon, 2023, Additive Manufacturing)
- Rheology and shrinkage of concrete using polypropylene fiber for 3D concrete printing(Mien V. Tran, Yen T. H. Cu, Chaux Virginie Le, 2021, Journal of Building Engineering)
- Large scale 3D printed concrete wall: Interlayer bonding and shrinkage(Thi Thuy Duong Dang, Mien Van Tran, T. Nguyen, H. Nguyen, 2026, Case Studies in Construction Materials)
层间弱界面与打印各向异性开裂的力学机理与断裂行为表征
合并三组中关于“弱界面—各向异性”成因与断裂描述的文献:包括层间界面形成与跨尺度后果综述、界面黏结—剪切力学模型与失效过程、界面微观结构表征,以及层间时间间隔/加载方向引起的力学各向异性、穿层与沿层断裂参数、PAN纤维混凝土各向异性断裂行为。共同点是从断裂力学与微观结构角度解释层间剥离与沿层裂纹通道的形成机制。
- Weak Interlayer Interfaces in 3D-Printed Concrete: Formation Mechanisms, Cross-Scale Consequences, and Control Strategies(Rongfei Zhang, Chao Liu, Zhen-Hua Duan, Zhen-Yuan Lv, Wei Zhang, Hua-Wei Liu, 2026, Coatings)
- Anisotropic Behavior of 3D-Printed Concrete: Interlayer Bonding, Pore Architecture, Reinforcement Limitations, and Durability Mechanisms(A. Mardani, M. Hematibahar, Selin Özteber, Q. A. A. Qais, Ivan Khalil, T. Gebre, A. Elsheikh, 2026, Materials)
- Mechanical behavior and unified shear model for the interface between 3D printed permanent formwork and cast concrete(Tao Li, Yue Li, Chao Yan, Xiaolong Wang, Bo Liu, Jia-Jun Shu, 2026, Materials Structure)
- Interfacial bond effects on the shear strength and damage in 3D-printed concrete structures: A combined experimental and numerical study(Qamar Shahzad, Fang-Yuan Li, 2025, Engineering Fracture Mechanics)
- Effect of Interfacial Failure on Stress-Strain Behavior of 3D-Printed Mortar Laminates(Ren Uematsu, T. Fukuyama, Hiroharu Kamada, 2026, Journal of Asian Concrete Federation)
- Mechanical and microstructural characterization of interlayer bonding in multi-material 3D-Printed concrete(Hou-Qi Sun, Jun-Jie Zeng, Shan-Shan Xie, Jun-Run Xia, Shi-Wei Yu, Y. Zhuge, 2026, Cement & Concrete Composites)
- Fresh and anisotropic-mechanical properties of 3D printable ultra-high ductile concrete with crumb rubber(Jun-Hong Ye, Can Cui, Jiangtao Yu, Kequan Yu, J. Xiao, 2021, Composites Part B: Engineering)
- Trans-layer and inter-layer fracture behavior of extrusion-based 3D printed concrete under three-point bending(Yu-Xiang Tang, Jian-Zhuang Xiao, Tao Ding, Hao-Ran Liu, Ming-Zhong Zhang, Jun-Hui Zhang, 2024, Engineering Fracture Mechanics)
- Anisotropy of Mechanical Properties of 3D-Printed Materials—Influence of Application Time of Subsequent Layers(Marcin Maroszek, I. Hager, K. Mróz, M. Sitarz, M. Hebda, 2025, Materials)
- Anisotropic fracture behavior of PAN fiber reinforced 3D printed concrete: Crack evolution and fiber orientation toughening mechanism(Guo-Sheng Wang, Zi-Yi Zhang, Junwei Tao, Gang Tian, Y. Nie, Qi-Lin Yang, Tongqiang Xia, Wei Ma, Chaojie Jia, 2026, Construction and Building Materials)
基体配合比设计、凝结调控与流变性能优化抑裂
合并三组中所有从新鲜态材料设计入手的文献:利用水泥固有凝结机制(闪凝、假凝、BCSA替代)与偏高岭土/硅灰/矿渣等辅助胶凝材料的堆积黏聚与火山灰反应,进行配合比优化;以屈服应力与触变建结构调控(膨润土/CMC、SAP、自密实地聚物、废玻璃粉、低黏土开挖土、微生物矿化)在兼顾可打印性与可建造性的同时降低收缩敏感性与层间缺陷。共同点是从材料源头削弱开裂驱动力。
- Investigating inherent cement setting mechanisms to improve the constructability performance of extrusion-based 3D concrete printing(F. Günzel, G. M. Moelich, S. S. Kanyenze, P. J. Kruger, R. Combrinck, 2024, Innovative Infrastructure Solutions)
- Enhancing printability of 3D printed concrete by using metakaolin and silica fume(Marwah M. Thajeel, K. Kopecskó, György L. Balázs, 2025, Structural Concrete)
- GGBFS –silica fume blended cementitious composite for extrusion‐based 3D concrete printing(P. Rajesh, Sajitha R. Nair, P. Nagarajan, S. Goudar, Sudha Das, 2026, Environmental Progress & Sustainable Energy)
- Optimization of Mix Proportion and Performance Study of 3D-Printed Concrete for Slope Protection(Yu-Hang Xia, Dong-Wei Cao, 2026, Journal of materials engineering and performance (Print))
- Low-clay soil as fine aggregate in 3D printed concrete: insights into fresh and hardened properties(Sandeep Kumar, Abhishek Kumar, Aakanksha Pundir, Ashutosh Dwivedi, P. Soda, S. M., Souradeep Gupta, A. Dixit, 2025, Journal of Sustainable Cement-Based Materials)
- A strategy for the improvement of the bonding performance of 3D-printed concrete interlayer interfaces(Jing Cao, E. Shengzhao, Yi Yang, Yaming Shi, J. Chai, Zeng-Guang Xu, 2024, Journal of Building Engineering)
- Rheology and pumpability of mix suitable for extrusion-based concrete 3D printing – A review(Spandana Paritala, Kailash Kumar Singaram, Indira Bathina, Mohd Ataullah Khan, S. Jyosyula, 2023, Construction and Building Materials)
- Microbial-induced calcareous precipitation effect on tensile strength and early age shrinkage of 3D printed concrete(He-Rui Zhao, Quan Jiang, Yong Xia, Dong-Qi Hou, Jun Luo, Jian Liu, 2025, Journal of Building Engineering)
- Rheology control and 3D concrete printing with fly ash-based aqueous nano-silica enhanced alkali-activated binders(Tippabhotla A. Kamakshi, K. Subramaniam, 2024, Materials Structure)
- Can superabsorbent polymers be used as rheology modifiers for cementitious materials in the context of 3D concrete printing?(Yu Chen, Min-Fei Liang, Yu Zhang, Zhen-Ming Li, B. Šavija, E. Schlangen, O. Çopuroğlu, 2023, Construction and Building Materials)
- Self-compacting geopolymer concrete for 3D concrete printing: rheological requirements, mix design challenges, and future prospects(Shahida Khan, M. Tantray, 2026, Innovative Infrastructure Solutions)
- Material properties, rheology, printability, and mechanical performance of waste glass powder in 3D concrete printing: a comprehensive review(A. M. Mohamed, B. Tayeh, R. Qasem, Y. I. Abu Aisheh, Mohd Azreen bin Mohd Ariffin, 2026, REVIEWS ON ADVANCED MATERIALS SCIENCE)
- Effects of CO₂ treatment on the interlayer bonding in 3D-printed alkali-activated concrete(Cai-Long Ma, Hou-Qi Sun, Shan-Shan Xie, Hong-Chao Zhao, Jun-Jie Zeng, 2026, Construction and Building Materials)
短切纤维增强与塑性/干燥收缩开裂抑制
合并三组中以随机分布短切纤维抑制收缩开裂的文献:纤维素纤维改善含水分布与收缩变形、聚丙烯/PAN/钢纤维、混杂PVA纤维、木纤维与玄武岩纤维、应变硬化水泥基复合材料(SHCC)、轻质ECC与高延性混凝土的自增强效果,以及再生/天然细骨料、钢纤维流变—力学多参数评价与纤维—配合比综合评估。共同点是通过纤维桥接、内应力重分布与应变硬化提升抗裂韧性,属“材料层面增韧”。
- Zigzag Reinforcement Method for 3D Concrete Printing(Bahram Ahadi, Mercedes Valiente López, 2025, Buildings)
- Steel Fiber Reinforcement for Improved Structural Performance and Durability of 3D Printed Mortar in Marine Environments(Nivin Philip, Agnieszka Jędrzejewska, Ashitta Mariam Mathew, Susan K. Uthuppan, 2025, Iranian Journal of Science and Technology: Transactions of Civil Engineering)
- 3D Printable Ca(OH)2-based geopolymer concrete with steel fiber reinforcement(Youssef Mortada, Ahmad Hammoud, Laith Masoud, M. Wyrzykowski, D. Sirtoli, P. Lura, Bilal Mansoor, E. Masad, 2025, Materials Structure)
- Investigating the effects of hybrid PVA/BF fibers in low-carbon 3D printed concrete with recycled aggregates: Rheology, strength, and anisotropy(Juan-Lan Zhou, Xiang-Wen Shi, Hong-Ru Zheng, Ruo-Yu Jin, O. Ebohon, Q. Zhan, Dao-Chuan Zhou, 2025, Construction and Building Materials)
- Development of strain-hardening cementitious composites (SHCC) as bonding materials to enhance interlayer and flexural performance of 3D printed concrete(Fei Teng, Junhong Ye, Jie Yu, Heng Li, Yi-Wei Weng, V. Mechtcherine, 2024, Cement & Concrete Composites)
- Fibre-reinforced lightweight engineered cementitious composites for 3D concrete printing(Junbo Sun, F. Aslani, Jesse Lu, Lining Wang, Yi-Miao Huang, Guo-Wei Ma, 2021, Ceramics International)
- Shrinkage and Cracking Properties of Cellulose Fiber–Concrete Composites for 3D Printing by Leveraging Internal Curing(Li Wang, Qi-Qi Li, Yu-zhuo Hu, Tianlong Cui, Rong Li, 2022, 3D Printing and Additive Manufacturing)
- Quantification of plastic shrinkage and plastic shrinkage cracking of the 3D printable concretes using 2D digital image correlation(S. Markin, V. Mechtcherine, 2023, Cement & Concrete Composites)
- Effects of Incorporating Fine Aggregates and Polypropylene Microfibres on the Cracking Control of 3D Printed Cementitious Mixtures(Armando Vargas, R. Robayo-Salazar, Ruby Mejía de Gutiérrez, 2024, Buildings)
- Recent Advancements in Polypropylene Fibre-Reinforced 3D-Printed Concrete: Insights into Mix Ratios, Testing Procedures, and Material Behaviour(Ben Hopkins, Wen Si, Mehran Khan, C. McNally, 2025, Journal of Composites Science)
- Multi-Parameter Evaluation of Steel Fibre-Reinforced Cementitious Materials for Extrusion-Based 3D Concrete Printing(Wen Si, Mehran Khan, C. McNally, 2026, Materials)
- Assessment of Fiber Reinforcement and Mixture Performance Requirements for Fiber-Reinforced 3D-Printed Concrete Applications(S. B. Nia, B. Shafei, 2026, Journal of Building Engineering)
- Engineering 3D-Printed UHPC: Optimising Fibre Content and Printing Direction for Enhanced Mechanical Performance(Jie Wu, Zhang-Yu Wu, Yanjie Qiao, Weiqi Dong, R. Yu, Yu-Jie Huang, Hui Zhang, 2026, Journal of Advanced Materials Research)
- Effects of Different Types of Fibers on Fresh and Hardened Properties of Cement and Geopolymer-Based 3D Printed Mixtures: A Review(Amir Ramezani, Shahriar Modaresi, Pooria Dashti, Mohammad Rasul GivKashi, F. Moodi, A. Ramezanianpour, 2023, Buildings)
- Enhanced mechanical properties of 3D printed concrete sculpture material with wood fibers reinforcement(Kejia Zhang, Muhammad Fadhil Wong bin Abdullah, 2024, BioResources)
- Study on Mechanical Properties of Composite Basalt Fiber 3D-Printed Concrete Based on 3D Meso-Structure(Sheng-Xuan Ding, Ji-Ren Li, Ming-Qian Wang, 2025, Materials)
跨层连续增强、界面粘结强化与结构配筋技术
合并各组中直接强化弱界面的“结构性”策略:打印过程中插入U型钉的桥接销栓作用、同步嵌入柔性FRP网格、宽幅多孔碳纤维/玻纤网格实现自动化连续配筋、按主应力轨迹设计路径与纤维砂浆协同取向、连续钢筋创新布筋(锯齿形布筋),以及层间粘结性能与可靠性提升、界面处理与齿形喷嘴/喷嘴悬距等工艺—构造措施。共同点是跨越或强化界面本身,显著提升抗弯抗拉抗剪强度与峰后韧性。
- Innovative reinforcement techniques for 3D-printed concrete: The impact of shape memory alloys on flexural strength and crack mitigation(Ronak Motiani, Saha Keunang Sylvain, S. P. Dalal, Jaykumar Vora, R. Chaudhari, 2025, Next Materials)
- Interlayer reinforcement of 3D printed concrete by the in-process deposition of U-nails(Li Wang, Guo-Wei Ma, Tian-shuang Liu, R. Buswell, Zhi-Jiang Li, 2021, Cement and Concrete Research)
- 3D-printed concrete with in-process embedded fiber-reinforced polymer grid reinforcement(Hou-Qi Sun, Shan-Shan Xie, Jun-Jie Zeng, Y. Zhuge, 2026, Communications Engineer)
- Evaluating the Effect of Glass and Carbon Fiber Mesh on 3D-Printed Concrete Performance(Emad Janghorban, Arpan Joshi, Florindo Gaspar, 2026, Materials)
- Fiber Reinforcement of 3D Printed Concrete by Material Extrusion Toolpaths Aligned to Principal Stress Trajectories(Daniel Auer, F. Bos, M. Olabi, Oliver Fischer, 2023, Open Conference Proceedings)
- Advancing Structural Reinforcement in 3D-Printed Concrete: Current Methods, Challenges, and Innovations(Bo Nan, Youxin Qiao, Junjie Leng, Yi-Kui Bai, 2025, Materials)
- Interlayer Bonding Properties of 3d Printed Concrete with Recycled Coarse Aggregates(Hua-Wei Liu, Chao Liu, Yi-Wen Wu, G. Bai, Chunhui He, Yi-Zhou Yao, Rong-Fei Zhang, Youqiang Wang, 2022, Social Science Research Network)
- Synergistic approach to enhancing interlayer bonding in 3D printed concrete via water to binder ratio and water retention addition(Thi Thuy Duong Dang, Mien Van Tran, T. Nguyen, 2026, Scientific Reports)
- Improving Reliability in Interlayer Bonding in 3D Printed Concrete (3DPC) through Interstitial Layer Modification(Shen Wang, O. Onuaguluchi, Nemkumar Banthia, Ya-Mei Zhang, 2026, Journal of Building Engineering)
- Enhancing interlayer bonding of 3D printed concrete via triblock copolymer networks(Jing-Gang Xu, Qiao Wang, Li Wang, 2026, Construction and Building Materials)
- Enhancing interlayer bonding in 3-dimensional printed concrete using bacteria-based biomineralization(Amardeep Singh, Kamal Anand, Qiong Liu, Vivian W. Y. Tam, S. Goyal, M. Reddy, 2025, Cement & Concrete Composites)
- Toothed nozzle optimization for enhancement of interlayer tensile strength of 3D-printed concrete with CTGAN and XGBoost model(You-Bao Jiang, Zupan Zhang, Jun Wen, Pengxiang Gao, Jie Tan, 2026, Case Studies in Construction Materials)
- Effect of nozzle stand-off distance, printing interval, and inclusion of glass fiber mesh reinforcement in 3D printed concrete(M. P. Salaimanimagudam, J. Jayaprakash, 2025, Construction and Building Materials)
打印工艺参数、路径取向与冷缝缺陷控制
合并各组中以工艺为变量的文献:打印方向(纵向/横向)决定层间是否成为优先裂缝通道、挤出成型技术与策略梳理、层间时间间隔与冷缝模拟、“有/无层间黏结”对比在冻融—湿润加速老化下的裂缝萌生与耐久性退化。共同点是不改动材料配方,而通过工艺窗口与路径设计减少弱界面和初始缺陷。
- Assessment of printing direction in flexural tests of 3D printed reinforced concrete beams(Pedro Henrique Cota Drumond, Geysiane Faria Barros Milagres, Paloma Renata Parassen, Luana Nascimento Procópio Santos, D. S. de Oliveira, J. M. de Carvalho, Gustavo de Souza Veríssimo, J. L. Lopes Ribeiro, 2025, Revista IBRACON de Estruturas e Materiais)
- Techniques and strategies in extrusion based 3D concrete printing of complex components to prevent premature failure(Abdallah Kamhawi, Mania Aghaei Meibodi, 2024, Automation in Construction)
- 3D CONCRETE PRINTING: A STUDY OF PRINTED STRUCTURES DURABILITY(A. Adamtsevich, A. Pustovgar, L. Adamtsevich, Y. Markov, 2025, International Journal for Computational Civil and Structural Engineering)
- Numerical assessment of plastic yielding in extrusion-based 3D concrete printing(Ya-Xin Tao, Jiangang Zhou, Wei-Jiu Cui, Xin-Yu Shi, G. de Schutter, K. Van Tittelboom, 2024, Materials Structure)
养护制度、表面养护剂与自愈能力的裂缝控制
保留在原始分组中较独特但未被其他组覆盖的论点:薄膜封闭养护、石蜡基养护剂等抑制早龄期失水收缩开裂的外部条件干预,以及打印构件自愈能力的评价,共同构成“后期干预+材料自修复”的减裂策略,与配比设计、结构增强等前置手段形成互补。
- Influence of curing methods on the compressive strength development of 3D-printed concrete unit cells(L. Pham, Thu Thi My Nguyen, 2026, JOURNAL OF MATERIALS & CONSTRUCTION)
- Effectiveness of Paraffin-based Curing Compound for Mitigation of the Plastic Shrinkage and Related Cracking of the 3D-printed Concrete Elements(S. Markin, Viktor Mechtcherine, 2023, 16th International Conference on Durability of Building Materials and Components)
- Evaluation of self-healing capacity of 3D printable bio-based fiber-reinforced cement-lime mortars(Alvaro Márquez, L. Ramallo, Yaiza Cerqueira, J. Puentes, I. Palomar, G. Barluenga, 2025, MATEC Web of Conferences)
断裂与开裂数值模拟:损伤塑性、内聚力/相场与多物理场耦合
合并各组中所有计算力学文献:CDP损伤塑性本构与晶格结构参数敏感性、内聚力区与相场内聚力模型、非普通态近场动力学、弥散裂纹有限元与闭合型断裂模型、层间孔洞形貌对裂纹路径的控制、带填充图案墙体面内非线性响应与超高性能材料构件模拟,以及耦合水化动力学—界面损伤的早龄期热-力建模与徐变变形计算算法。共同点是以可标定、可外推的数值模型量化裂缝萌生扩展与层间退化。
- Nonlinear in-plane response of 3D-printed concrete walls with varied infill patterns: Experimental mix design and numerical structural assessment(İ. Tarhan, Yeşim Tarhan, 2025, Challenge Journal of Structural Mechanics)
- Numerical simulation of 3D printed ultra high-performance concrete using the lattice discrete particle model(Bahar Ayhan, Elmer M. Irizarry, E. Lale, Ke Yu, Matthew Troemner, G. Cusatis, 2025, Proceedings of the 12th International Conference on Fracture Mechanics for Concrete and Concrete Structures)
- Coupled Thermo-Mechanical Modelling of Early-Age Interlayer Degradation in 3D-Printed Concrete(Joseph Osamwonyi Ediae, 2026, Buildings)
- Numerical Modeling and Parameter Sensitivity of Selective Paste Intrusion 3D-Printed Concrete(Yun-Zhe Wang, Ticho Ooms, Bo Zhang, Yi-Lin Wang, R. Wan-Wendner, W. De Corte, 2026, Applied Sciences)
- Numerical investigation of structural behavior of 3D-printed concrete walls: insights from damage mechanics and cohesive zone approaches(S. S. Kumar, N. Muthu, B. Panda, 2025, Progress in Additive Manufacturing)
- Computational Algorithms for Early-Age Creep and Buildability Prediction in Extrusion-Based 3D Concrete Printing: A Critical Survey(M. Adeel, Ajay Kumar, Prodhan Md Atowar Rahman, Asad Ali, Akif Khalique Kamboh, 2026, Journal of Algorithms in Complex Systems)
- Non-Ordinary State-Based Peridynamics Simulation for Crack Propagation of 3D-Printed Fiber-Reinforced Concrete Beam Under Bending(T. Zhu, Yu-Ching Wu, P. Zhi, Peng Zhu, Mei-Yan Bai, Cheng Qi, 2026, Buildings)
- Experimentally verified FE model of bending reinforced 3D-printed concrete elements(Victor Telichko, G. Slavcheva, Artem Levchenko, 2025, Mechanics of Advanced Materials and Structures)
- Mechanical characterisation for numerical simulation of extrusion-based 3D concrete printing(Marchant van den Heever, F. Bester, J. Kruger, G. V. Van Zijl, 2021, Journal of building engineering)
- The Influence of Pore Characteristics on the Mechanical Properties of 3D-Printed Concrete Based on the Phase-Field Method(Lei Luo, Yao Li, Wen-Bin Xu, Y. You, Wen-Qiang Xu, De-Yong Hu, 2026, Materials)
- Closed-form fracture model for evaluating crack resistance of 3D printed fiber-reinforced alkali-activated slag/fly ash recycled sand concrete(Zheng-Yuan Chen, Shu-Tong Yang, Qi Liu, Ming-Qi Xu, Sheng Wang, Tian Lan, 2024, Journal of Building Engineering)
- Experimental and FEM evaluation of the influence of interlayer bonding strength in 3D printed concrete members under compressive and flexural loadings(Quoc Bao To, Khoa V. A. Pham, Gayoon Lee, Myoungsu Shin, D. W. Shin, Kihak Lee, 2024, Journal of Building Engineering)
机器学习与视觉智能监测驱动的开裂相关性能预测
合并各组中数据驱动与智能感知文献:以可解释机器学习(XGBoost-GTO、SVM、SHAP)预测抗折/抗拉强度与层间粘结强度并识别影响开裂的关键配比因素,以及基于视觉检测的打印过程与缺陷自动识别监测综述。共同点是用数据与视觉手段替代耗时试错,实现开裂风险与质量的快速预判。
- Interpretable Machine Learning for Flexural Strength Prediction of 3D-Printed Concrete Incorporating Supplementary Cementitious Materials(Fengping Qin, Yang Chen, Meng-Di Hou, Jian-Bo Huang, 2026, Buildings)
- Hybrid machine learning model using gorilla troops optimizer for accurate prediction of interlayer bonding strength in 3D-printed concrete(M. Khan, I. Ullah, 2025, Fusion Journal of Engineering and Sciences)
- Machine Learning-Based Predictive Model for Tensile and Flexural Strength of 3D-Printed Concrete(A. Ali, Raja Dilawar Riaz, U. Malik, Syed Baqar Abbas, M. Usman, M. Shah, In-Ho Kim, Asad Hanif, Muhammad Qasim Faizan, 2023, Materials)
- A comprehensive review on integrating vision-based sensing in extrusion-based 3D printing processes: toward geometric monitoring of extrusion-based 3D concrete printing(Paniz Farrokhsiar, Benay Gursoy, José Pinto Duarte, 2024, Construction Robotics)
各向异性力学性能、耐久性与标准符合性试验评价
合并各组中的试验基准与性能验证文献:RILEM TC 304-ADC 多实验室联合研究比较不同加载方向强度与离散性、带缺陷足尺构件的三点弯曲/碎片试验与无损检测(超声、密度、吸水)相关性、含膨胀珍珠岩细粒混凝土的抗冻融与开裂成因分析、打印混凝土长期耐久性(冻融、化学侵蚀、碳化、氯离子渗透)新兴认识,以及既有标准符合性与结构可靠性评估。共同点为开裂优化措施提供可比较的验证与诊断依据。
- Mechanical properties of 3D printed concrete: a RILEM TC 304-ADC interlaboratory study — flexural and tensile strength(R. Wolfs, J. Versteege, Manu Santhanam, Shantanu Bhattacherjee, F. Bos, A. Robens-Radermacher, Shravan Muthukrishnan, Costantino Menna, Onur Ozturk, N. Ozyurt, Josef Roupec, Christiane Richter, J. Jungwirth, Luiza Miranda, Rebecca Ammann, J. Caron, V. de Bono, Renate Monte, Iván Navarrete, Claudia Eugenin, H. Lombois-Burger, Bilal Baz, Māris Šinka, Alise Sapata, Ilhame Harbouz, Ya-Mei Zhang, Zijian Jia, J. Kruger, Jean-Pierre Mostert, Katarina Šter, A. Šajna, Abdelhak Kaci, Said Rahal, Chalermwut Snguanyat, Arun R. Arunothayan, Zeng-Feng Zhao, Inka Mai, I. Rasehorn, David Böhler, Niklas Freund, Dirk Lowke, T. Neef, Markus Taubert, Daniel Auer, C. Hechtl, Maximilian Dahlenburg, Laura Esposito, R. Buswell, J. Kolawole, Muhammad Nura Isa, Xing-Zi Liu, Zhen-Di Wang, Kolluru V. L. Subramaniam, Viktor Mechtcherine, 2025, Materials Structure)
- Diagnostics and experimental analysis of 3D printed concrete structural elements(K. Hrabová, Matěj Velát, P. Schmid, P. Daněk, R. Dvořák, 2025, Frattura ed Integrità Strutturale)
- Durability and Cracking Defects in 3D‐Printed Concrete(G. Skripkiūnas, A. Tolegenova, Lyudmyla Rishko, Kenzhebek Akmalaiuly, Daiva Baltuškienė, 2025, Advance in Civil Engineering)
- Anisotropic Behavior in 3D Printed Concrete: Finite Element Simulation Approach(Fang-Yuan Li, Xiangcheng Hu, Qamar Shahzad, 2024, Journal of materials engineering and performance (Print))
- Emerging Insights into the Durability of 3D-Printed Concrete: Recent Advances in Mix Design Parameters and Testing(James Bradshaw, Wen Si, Mehran Khan, C. McNally, 2025, Designs)
- Conformance Evaluation of 3D Printed Concrete: Interlayer Bond Strength and Compressive Strength(Hussain Ashoor Mohamed, Rouya Hdeib, Ali Ahmed Aljouri, 2025, 2025 International Conference on Decision Aid Sciences and Applications (DASA))
- Mechanical properties of extrusion-based 3D-printed concrete considering the thickness of the printed layer and printing time interval(Boyang Tang, Jia-Chuan Yan, Xiaoyu Han, Yini Lin, Feng Fan, 2025, Structures)
增强与性能提升策略的系统性综述与方法学框架
保留各原始组中的宏观归纳性文献:系统梳理打印混凝土的增强方法(钢筋、纤维、层间、工艺)、性能提升途径,以及纳米材料与拓扑优化的协同整合与关键评述,为开裂优化提供分类体系与方法学框架,与前述具体技术路线分组形成“总—分”互补关系。
- State of the Art Review of Reinforcement Strategies and Technologies for 3D Printing of Concrete(Zheng-Yu Wu, A. Memari, J. Duarte, 2022, Energies)
- Improving performance of additive manufactured (3D printed) concrete: A review on material mix design, processing, interlayer bonding, and reinforcing methods(Shanaka Kristombu Baduge, S. Navaratnam, Yousef Abu-Zidan, T. McCormack, Kate T. Q. Nguyen, P. Mendis, G. Zhang, L. Aye, 2021, Structures)
- A Critical Review on Synergistic Integration of Nanomaterials in 3D-Printed Concrete: Rheology to Microstructure and Eco-Functionality(Siva Jamjala, Manivannan Thulasirangan Lakshmidevi, K. S. K. Karthik Reddy, Bidur Kafle, R. Al-Ameri, 2025, Applied Sciences)
将三组初始化分组去重合并为十条并列技术路线,形成"机理—材料—结构—工艺—后期干预—数值—数据—验证—综述"的完整格局:(1) 收缩与早龄期开裂机理及塑性收缩/毛细压力测量与风险量化,明确开裂驱动力;(2) 层间弱界面与打印各向异性的力学机理、界面剪切模型与穿层/沿层断裂行为表征,回答"为何在界面处开裂";(3) 基体配合比设计、凝结机制调控与流变/触变建结构优化,从材料源头降低开裂敏感性;(4) 短切纤维与应变硬化水泥基复合材料的桥接增韧,抑制塑性/干燥收缩开裂;(5) 跨层连续增强(U型钉、FRP/碳纤维网格、应力轨迹布筋、锯齿形钢筋)与层间粘结、喷嘴工艺强化;(6) 打印方向、层间时间间隔与冷缝等工艺参数及路径取向控制;(7) 养护制度、表面养护剂与自愈能力等后期干预手段;(8) 损伤塑性、内聚力/相场、近场动力学与热-力-水化多物理场耦合数值模拟;(9) 可解释机器学习与视觉智能监测的性能预测与缺陷识别;(10) 各向异性、耐久性与标准符合性试验评价,并由综述类文献提供总体方法学框架。各分组相互并列、不交叉,覆盖了优化方法从成因到验证的全链条。
合并三组中所有以“为什么开裂”为核心的机理与测量文献:涵盖塑性/干燥/自收缩变形机理与环境影响、毛细压力发育建模、大型打印构件与受限收缩开裂行为,以及激光/非接触数字图像相关等塑性收缩开裂量化测试方法与开裂风险模型。共同点为阐明开裂驱动力并提供可比较的测量—风险评价链条,是全部优化方法的基础。相关文献:Mohsen Rezaei Shahmirzadi et. al, 2021 等 12 篇文献
合并三组中关于“弱界面—各向异性”成因与断裂描述的文献:包括层间界面形成与跨尺度后果综述、界面黏结—剪切力学模型与失效过程、界面微观结构表征,以及层间时间间隔/加载方向引起的力学各向异性、穿层与沿层断裂参数、PAN纤维混凝土各向异性断裂行为。共同点是从断裂力学与微观结构角度解释层间剥离与沿层裂纹通道的形成机制。相关文献:Rongfei Zhang et. al, 2026 等 10 篇文献
合并三组中所有从新鲜态材料设计入手的文献:利用水泥固有凝结机制(闪凝、假凝、BCSA替代)与偏高岭土/硅灰/矿渣等辅助胶凝材料的堆积黏聚与火山灰反应,进行配合比优化;以屈服应力与触变建结构调控(膨润土/CMC、SAP、自密实地聚物、废玻璃粉、低黏土开挖土、微生物矿化)在兼顾可打印性与可建造性的同时降低收缩敏感性与层间缺陷。共同点是从材料源头削弱开裂驱动力。相关文献:F. Günzel et. al, 2024 等 13 篇文献
合并三组中以随机分布短切纤维抑制收缩开裂的文献:纤维素纤维改善含水分布与收缩变形、聚丙烯/PAN/钢纤维、混杂PVA纤维、木纤维与玄武岩纤维、应变硬化水泥基复合材料(SHCC)、轻质ECC与高延性混凝土的自增强效果,以及再生/天然细骨料、钢纤维流变—力学多参数评价与纤维—配合比综合评估。共同点是通过纤维桥接、内应力重分布与应变硬化提升抗裂韧性,属“材料层面增韧”。相关文献:Bahram Ahadi et. al, 2025 等 16 篇文献
合并各组中直接强化弱界面的“结构性”策略:打印过程中插入U型钉的桥接销栓作用、同步嵌入柔性FRP网格、宽幅多孔碳纤维/玻纤网格实现自动化连续配筋、按主应力轨迹设计路径与纤维砂浆协同取向、连续钢筋创新布筋(锯齿形布筋),以及层间粘结性能与可靠性提升、界面处理与齿形喷嘴/喷嘴悬距等工艺—构造措施。共同点是跨越或强化界面本身,显著提升抗弯抗拉抗剪强度与峰后韧性。相关文献:Ronak Motiani et. al, 2025 等 13 篇文献
合并各组中以工艺为变量的文献:打印方向(纵向/横向)决定层间是否成为优先裂缝通道、挤出成型技术与策略梳理、层间时间间隔与冷缝模拟、“有/无层间黏结”对比在冻融—湿润加速老化下的裂缝萌生与耐久性退化。共同点是不改动材料配方,而通过工艺窗口与路径设计减少弱界面和初始缺陷。相关文献:Pedro Henrique Cota Drumond et. al, 2025 等 4 篇文献
保留在原始分组中较独特但未被其他组覆盖的论点:薄膜封闭养护、石蜡基养护剂等抑制早龄期失水收缩开裂的外部条件干预,以及打印构件自愈能力的评价,共同构成“后期干预+材料自修复”的减裂策略,与配比设计、结构增强等前置手段形成互补。相关文献:L. Pham et. al, 2026 等 3 篇文献
合并各组中所有计算力学文献:CDP损伤塑性本构与晶格结构参数敏感性、内聚力区与相场内聚力模型、非普通态近场动力学、弥散裂纹有限元与闭合型断裂模型、层间孔洞形貌对裂纹路径的控制、带填充图案墙体面内非线性响应与超高性能材料构件模拟,以及耦合水化动力学—界面损伤的早龄期热-力建模与徐变变形计算算法。共同点是以可标定、可外推的数值模型量化裂缝萌生扩展与层间退化。相关文献:İ. Tarhan et. al, 2025 等 12 篇文献
合并各组中数据驱动与智能感知文献:以可解释机器学习(XGBoost-GTO、SVM、SHAP)预测抗折/抗拉强度与层间粘结强度并识别影响开裂的关键配比因素,以及基于视觉检测的打印过程与缺陷自动识别监测综述。共同点是用数据与视觉手段替代耗时试错,实现开裂风险与质量的快速预判。相关文献:Fengping Qin et. al, 2026 等 4 篇文献
合并各组中的试验基准与性能验证文献:RILEM TC 304-ADC 多实验室联合研究比较不同加载方向强度与离散性、带缺陷足尺构件的三点弯曲/碎片试验与无损检测(超声、密度、吸水)相关性、含膨胀珍珠岩细粒混凝土的抗冻融与开裂成因分析、打印混凝土长期耐久性(冻融、化学侵蚀、碳化、氯离子渗透)新兴认识,以及既有标准符合性与结构可靠性评估。共同点为开裂优化措施提供可比较的验证与诊断依据。相关文献:R. Wolfs et. al, 2025 等 7 篇文献
保留各原始组中的宏观归纳性文献:系统梳理打印混凝土的增强方法(钢筋、纤维、层间、工艺)、性能提升途径,以及纳米材料与拓扑优化的协同整合与关键评述,为开裂优化提供分类体系与方法学框架,与前述具体技术路线分组形成“总—分”互补关系。相关文献:Zheng-Yu Wu et. al, 2022 等 3 篇文献
总计 97 篇相关文献
This article explores the durability and cracking defects associated with 3D‐printed concrete, a rapidly emerging technology in construction. As the demand for innovative building techniques grows, understanding the long‐term performance of 3D‐printed structures becomes crucial. The most important properties of these products are the resistance to freezing and thawing and the possibility of cracking during maintenance. A fine‐grained concrete mixture with expanded perlite additive was tested on strength, freezing–thawing resistance, and the reasons for cracking were analyzed during maintenance. Some differences between the results from standard concrete specimens and the results from 3D‐printed concrete were obtained experimentally. During the research, 3D‐printed concrete specimens were produced with industrial equipment, the density and compressive strength were determined, the mass loss of concrete specimens after freeze/thaw cycles was tested. By reducing the water‐to‐cement ratio to 11%, the strength of concrete with expanded perlite additive increased from 68.2 to 71.1 MPa. For concrete with W/C equal to 0.47 after 28 freeze/thaw cycles, the mass loss of 3D‐printed specimens reaches 2.09 and 56 freeze/thaw cycles 9.17 kg/m2, and large surface defects were obtained. An analysis of the origin and recommendations for preventing cracks from occurring in 3D‐printed products were carried out. The findings underscore the need for optimized mix designs and printing parameters to enhance durability.
Although 3D-printed concrete (3DPC) offers advantages such as faster construction, reduced labour costs, and minimized material waste, concerns remain about its long-term durability. This review examines these challenges by assessing how the unique layer-by-layer manufacturing process of 3DPC influences key material properties and overall durability. The formation of interfacial porosity and anisotropic microstructures can compromise structural integrity over time, increasing susceptibility to environmental degradation. Increased porosity at layer interfaces and the presence of shrinkage-induced cracking, including both plastic and autogenous shrinkage, contribute to reduced durability. Studies on freeze–thaw performance indicate that 3DPC can achieve durability comparable to cast concrete when proper mix designs and air-entraining agents are used. Chemical resistance, particularly under sulfuric acid exposure, remains a challenge, but improvements have been observed with the inclusion of supplementary cementitious materials such as silica fume. In addition, tests for chloride ingress and carbonation reveal that permeability and resistance are highly sensitive to printing parameters, material composition, and curing conditions. Carbonation resistance, in particular, appears to be lower in 3DPC than in traditional concrete. This review highlights the need for further research and emphasizes that optimizing mix designs and printing processes is critical to improving the long-term performance of 3D-printed concrete structures.
This study investigates the effects of incorporating metakaolin (MK) and silica fume (SF) on the fresh and hardened properties of 3D printed concrete (3DPC). Five mix designs were prepared with MK replacement levels of 0%, 10%, 12.5%, and 15%, along with one mix containing 10% MK and 5% SF. Key performance metrics include flowability, green strength, pumpability, shape retention, buildability, extrudability, compressive strength, and interlayer bond strength. The results showed that increasing MK content generally enhanced early strength gain, shape retention, and buildability; however, a high MK dosage (15%) negatively affected extrudability and caused visible cracking. The mix with 10% MK and 5% SF (MK10SF5) demonstrated the best overall performance, achieving excellent shape retention (S1 = 0.99), the highest buildability (72 printed layers), and the highest compressive strengths: 85.4 MPa for cast specimens and 78.8, 64.4, and 73.0 MPa in the X, Y, and Z directions, respectively, for 3D printed specimens. It also recorded the highest interlayer bond strength of 2.14 MPa. The superior performance of MK10SF5 is attributed to the synergistic effects of MK and SF, which enhance particle packing, cohesion, and pozzolanic reactivity. These findings highlight the potential of MK and SF in optimizing 3DPC for improved printability and mechanical performance.
This review presents a comprehensive analysis of polypropylene (PP) fibre incorporation in three-dimensional printed concrete (3DPC), focusing on the material behaviour in both fresh and hardened states. PP fibres play a critical role in improving rheological properties such as buildability, flowability, and extrudability. While increased fibre content enhances interlayer bonding and shape retention through the fibre bridging mechanism, it also raises yield stress and viscosity, which may compromise extrudability. In the hardened state, PP fibres contribute to improvements in compressive and flexural strength up to an optimal dosage, beyond which performance may decline due to fibre clustering and reduced packing density. When aligned with the printing direction, fibres are particularly effective in mitigating shrinkage-induced cracking by redistributing internal tensile stress. However, their inclusion can lead to a slight increase in porosity and promote mechanical anisotropy. This review also discusses mix design parameters, fibre characteristics, and experimental protocols, while identifying key research gaps including the lack of standardized testing methods, limited understanding of fibre orientation effects, and insufficient exploration of hybrid fibre systems. Based on the synthesis of reported studies, optimal print quality and structural consistency have been associated with the use of 6 mm long fibres, nozzle diameters of 4 to 6 mm, and printing speeds ranging from 40 to 60 mm/s. Overall, PP fibre reinforcement shows strong potential for enhancing the structural integrity and dimensional stability of 3D-printed concrete, while emphasizing the need for further studies to optimize its use in practice.
: This paper presents a systematic study on the effect of layer-by-layer printing process on the fracture behavior of hardened extrusion-based 3D printed concrete (3DPC). Based on three-point bending tests on center-notched beams, the fracture response of printed specimens with two fracture patterns including crack propagation across layers (trans-layer fracture) and crack propagation along layers (inter-layer fracture) was compared with that of cast specimens. The fracture mechanism of 3DPC was explored using the fracture parameters and fracture process zone (FPZ) characteristics. Experimental phenomena can be explained by the additional interlaminar cracking in FPZ of concrete introduced by the layer-by-layer stacking process. It could produce a toughening effect if cracks propagate through layers, as it is beneficial to reduce stress concentration and improve deformability. In the printing process design of 3DPC, such feature can be rationally utilized to transform the process-induced weak interfaces from inherent defects to toughening means.
No abstract available
No abstract available
No abstract available
. 3D-printed concrete elements are highly vulnerable to early-age shrinkage and cracking compared to conventionally cast concrete elements. Material compositions of printable concretes and complete renunciation of shuttering are responsible for accelerated capillary pressure build-up, leading to volumetric constructions of the 3D-printed layers at a very early age after extrusion and enhanced shrinkage at a later age. Shrinkage-induced cracks can severely impair the durability and appearance of 3D-printed concrete structures. The study at hand analyses the efficacy of the paraffin-based curing agent for reducing the shrinkage and cracking of 3D-printed elements and structures. Development of the temperature and capillary pressure, as well as shrinkage strains, were reported for the cured and uncured specimens. The study results show that applying paraffin-based curing agents can considerably reduce shrinkage-indued deformations of the 3D-printed elements produced even under extreme environmental conditions.
Developments in the application of the 3D concrete printing (3DCP) technology in the construction industry over the past few years are providing a chance to increase productivity and cost efficiency. However, before reaching an industrial stage of the 3DCP technology several hurdles should be overcome. One of the major challenges is to guarantee high durability and long-life cycle of the printed elements. Since 3D-printed elements are subjected to very early and fast evaporation of the pore water, accelerated capillary pressure build-up may lead to severe plastic shrinkage and, consequently, a high cracking propensity of the 3D-printed elements. Durability and robustness would be severely impaired. Experimental quantification of the plastic shrinkage and related cracking is essential to identify appropriate mitigation strategies. The article at hand presents innovative approaches for quantification of the plastic shrinkage and related cracking of the printable cementitious compositions by means of contactless 3D digital image correlation technique. Various experimental setups were presented and their effectiveness for measurement of the plastic shrinkage and plastic shrinkage cracking were analysed.
This study presents a coupled numerical–experimental investigation into the early-age thermo-mechanical behaviour of 3D-printed concrete (3DPC), with particular emphasis on strength development, interlayer bonding, and thermally induced cracking that govern structural buildability and performance. A coupled multiphysics modelling framework was developed in COMSOL Multiphysics by integrating hydration kinetics, maturity theory, thermo-mechanical coupling, and a cohesive-zone-based interlayer damage formulation through user-defined time-dependent constitutive relationships and domain activation functions. The model simulated the temporal evolution of temperature, stiffness, stress development, and interlayer degradation during the early-age printing process. The model simulates the temporal evolution of temperature, stiffness, and interlayer damage and was validated against experimental results from compression, interlayer bond, and fracture tests conducted under varying printing time gaps and curing temperatures. The results demonstrate that increasing interlayer deposition intervals up to 60 min leads to reductions of approximately 38% in interlayer bond strength and a significant reduction in apparent compressive strength exceeding 80% between 0 and 60 min deposition delay. It should be noted that this reduction primarily reflects interlayer-dominated failure and loss of structural continuity rather than intrinsic degradation of the bulk cementitious matrix, primarily due to hydration discontinuity, moisture loss, and progressive substrate stiffening. Elevated curing temperatures further intensify thermal gradients, resulting in higher residual stresses and increased crack susceptibility at interlayer interfaces. The numerical predictions showed good agreement with the experimental responses, with peak-force prediction errors below 5% and RMSE values of approximately 0.30–0.45 kN along the post-peak softening, confirming the reliability of the proposed modelling approach. The findings highlight the critical importance of printing continuity and thermal control in governing early-age structural performance and provide quantitative guidance for optimising process parameters in extrusion-based 3D concrete printing.
This study provides a direct, quantitative comparison of three practical curing methods—Natural air-drying (ND), Membrane sealing (MB), and Water Immersion (WI)—on the compressive strength development of 3D-printed concrete (3DPC). Unit cell specimens were fabricated and subjected to the curing regimes immediately after printing, with strength evaluated at 7 and 28 days. Results demonstrate a substantial influence of the curing method. Membrane sealing (MB) proved most effective, yielding the highest strength (16.7 MPa and 19.7 MPa at 7 and 28 days, respectively). Using MB as a baseline (100%), a Relative Performance Index (RPI) revealed that Immersion (WI) and Natural curing (ND) retained only 89% and 80% of the 28-day strength, respectively. Qualitative analysis of failure modes showed cohesive vertical cracking without interlayer delamination, indicating that interlayer bonds remained competent and that the strength reduction under poor curing is primarily due to a generalized weakening of the cementitious matrix. This finding underscores that effective curing enhances overall material homogeneity. The pronounced performance deficit, particularly under natural drying, directly quantifies the critical vulnerability of 3DPC's layered microstructure to moisture loss. The findings deliver clear, data-driven evidence for implementing impermeable membrane curing as a vital and practical site practice to ensure the mechanical performance of digitally fabricated concrete.
No abstract available
Highlights ARMO-mesh 500/500 doubles flexural strength (up to a 100% increase). Glass fiber mesh yields only marginal gains (~3–12%). Larger beam-like specimens show a clear size effect (reduced strength). Wide porous carbon meshes enable automated reinforcement. Apparent superior interlayer bonding and post-cracking toughness are achieved. Corrosion resistance and sustainability benefits over steel are observed. Abstract Additive manufacturing of concrete offers reduced waste, faster construction, and design freedom, yet effective reinforcement integration remains a major challenge due to weak interlayer bonding and anisotropy. Most prior studies focus on vertical reinforcement, short fibers, or metallic systems, achieving modest flexural improvements (15–60%). This study evaluates horizontal continuous reinforcement using glass fiber mesh and two carbon fiber meshes (ARMO-mesh 200/200 and 500/500) integrated during 3D printing. The methods include extrusion-based printing of small (four-layer) and beam-like (eight-layer) specimens, both printed and cast, followed by three-point flexural and compression tests at 7 and 28 days under vertical and horizontal loading. The results show that ARMO-mesh 500/500 significantly enhances flexural strength—up to 100% over unreinforced controls (e.g., 24.4 kNm vs. 12.2 kNm in small specimens at 28 days) and ~60% over ARMO-mesh 200/200, while glass mesh provides only marginal gains (~12%). Carbon meshes also improve post-cracking toughness and apparent interlayer cohesion. A pronounced size effect reduces nominal strength in larger specimens. These findings demonstrate that wide-format porous carbon meshes offer a scalable, corrosion-resistant solution for load-bearing 3D-printed concrete elements, advancing automated digital construction.
Abstract 3D concrete printing is a promising technology recently developed to automate construction. Since no formwork is used in this technology to support and protect fresh concrete, there are two aspects which considerably accelerate the development of capillary pressure in 3D-printed concrete in comparison to conventionally placed concrete: i) high stiffness of 3D-printed needed to provide sufficient buildability, and ii) very early and fast evaporation of pore water. Accelerated development of capillary pressure may lead to severe plastic shrinkage cracking in 3D-printed elements and, hence, need to be mitigated. This investigation aims at providing a poromechanical model for capillary pressure development in 3D-printed elements. To simulate the development of capillary pressure and plastic shrinkage, environmental factors, material properties, and element geometry need to be considered as a whole. The model inputs – coefficient of permeability, static bulk modulus, air entry pressure and chemical shrinkage rate – were determined experimentally. The model was validated for two fine-grained concretes. Both 3D-printed materials yielded faster capillary pressure increase in comparison to cast concrete, while partial substitution of cement with silica fume further accelerated the capillary pressure development. Furthermore, due to the lower permeability of the mixture containing silica fume, the gradient of capillary pressure between 3D-printed layers increased, as did the gradient of plastic shrinkage.
No abstract available
No abstract available
Compared with conventional formwork casting materials, 3D printed concrete (3DPC) is characterized by large amounts of cementitious materials, a low aggregate–binder ratio, and a large water evaporation area, which make the printed materials and structures highly prone to plastic shrinkage and cracking. In this study, cellulose fibers were incorporated into concrete to improve its moisture distribution and increase its early-age strength. The effects of both dry and prewet cellulose fibers on properties of 3DPC were experimentally investigated. To ensure consistency in the amounts of dry fibers used, 0.5–2% dry cellulose fibers and 1–4% prewet cellulose fibers were adopted. The effects of the added cellulose fibers on printability, mechanical strength, shrinkage, and cracking performance of the 3DPC were experimentally studied. Particularly, a constraint method was developed to access the cracking behavior of 3DPC. Favorable shrinkage resistance was achieved, and the 120-day shrinkage decreased by 17.9% and 23.3% by addition of 2% dry fibers and 4% prewet fibers, respectively. Cracking was eliminated with addition of 4% prewet fibers, without influencing the printability and mechanical properties.
This state of the art review paper aims to discuss the results of a literature survey on possible ways to reinforce printed concrete based on existing reinforcement strategies. Just as conventional concrete, for 3D printed concrete to be suitable for large-scale construction, reinforcement is needed to increase the tensile capacity of concrete members and reduce temperature and shrinkage cracking. Despite efforts that are currently underway, the development of proper reinforcement suitable for printed concrete is still very active on the research agenda. As an initial step for designing suitable reinforcement for printed concrete, the existing reinforcement methods for printed concrete as well as conventional cast concrete from the literature are reviewed and summarized. Through the preliminary evaluation of the suitability and effectiveness of various reinforcement methods, guidelines are proposed to better understand possible solutions to reinforce printed concrete and inspire new practical ideas to fill the current technology void. The conclusions also include the possible improvements of the existing reinforcement methods to be considered in future applications.
Abstract Extrusion-based concrete 3D printing is at its infancy and many aspects of this new technology need to be thoroughly investigated to pave the way for its widespread use in construction. Since the inherent drying shrinkage of the hardened cement paste is the source of the drying shrinkage of 3D printed concrete, the shrinkage behavior of cementitious 3D printing materials with very high cement to fine aggregate ratios is one of the major challenges for researchers working on this innovative technology. Besides, due to the absence of formwork in this technique, an outdoor 3D printing environment causes excessive moisture loss and drying shrinkage cracking. This paper presents the first comprehensive investigation on the effects of different outdoor environmental conditions i.e. relative humidity (RH) and temperature on the moisture loss, drying and autogenous shrinkage of cementitious 3D printing materials, considering different sand to cement (S/C), and surface to volume (S/V) ratios of free-formed specimens. Mass loss and length change of mortars which were cured for up to 168 days under standard condition (24 C-50%RH with 24 h of sealed initial curing) were compared with those at 24 C-50%RH, 35 C-85%RH and 35 C-45%RH (free-formed specimens without initial curing) to investigate the effect of outdoor printing environment and the absence of formworks on the deformations caused by shrinkage. The drying shrinkage results indicate that 28 days free-formed specimens under different non-standard curing conditions show a length change up to 30% lower than specimens in the standard environment. Moreover, increasing the sand to cement ratio from 0.8 to 1.0 results in a 10% decrease in the drying shrinkage strain. This study also discusses the higher susceptibility of free-formed specimens to carbonation shrinkage and demonstrates that printed specimens have higher shrinkage deformation in the longer term compared to conventional casting specimens. The results of nitrogen adsorption-desorption analysis also prove that the total porosity in free-formed specimens in all environmental conditions reduces and reaches a finer pore structure after 112 days compared to conventional casting specimens. These results point to the importance of internal or external curing for reducing shrinkage in concrete 3D printing.
3D printing (3DP) of concrete is an innovative technology towards digitalisation and sustainability of construction industry. The design of printable materials is in the spotlight of research and some issues related to durability of 3DP members, such as cold joints between successive layers and cracking due to shrinkage, need to be overcome for widespread applications. Self-healing, also referred to as self-repairing capacity, combined with short-fiber reinforcement to control crack width, are some possible solutions to increase 3DP members durability. This study addresses this gap evaluating the self-healing capacity of cement-lime 3DP mortars reinforced with vegetal fibers and self-healing capacity. Printability was assessed through a rheological characterization using a Dynamic Shear Rheometer (DSR) and field-oriented tests, such as penetration and flow table tests. Extrudability and buildability were also studied by extrusion and uniaxial unconfined compression tests (UUCT). The evolution of mortar properties was monitored at Early age (EA) to better understand the hydration and shrinkage underlying mechanisms. Finally, small-scale prototypes were constructed by a robotic 3D printing arm and the self-healing capacity was evaluated. This work could have an impact on the design of new materials with self-healing capacity applied on digital fabrication techniques for more durable construction.
Plastic shrinkage cracking significantly affects the durability and performance of cement‐based materials, particularly in 3D concrete printing (3DCP), where environmental exposure and geometrical features exacerbate early‐age deformation. This study proposes a simplified experimental method to assess shrinkage crack risk of 3DCP mixes using cast specimens subjected to controlled environmental conditions. The approach enables monitoring of deformation from approximately 15 minutes after water addition, capturing the critical early‐age response. Shrinkage was continuously measured using a non‐contact laser‐based system, while mass loss and environmental parameters were recorded to quantify evaporation rates. Results show that the initial deformation rate increases with evaporation rate, and three distinct deformation behaviors were identified, depending on cracking occurrence and evolution. A critical condition for cracking was observed at evaporation rates above 0.15 kg/m2·h combined with concrete temperatures below 25 °C. The proposed methodology provides a robust, conservative, and practical tool for evaluating plastic shrinkage susceptibility under realistic conditions.
Autogenous shrinkage may be a critical issue concerning the use of limestone-calcined clay-cement (LC3) in high-performance concrete and 3D printable cementitious materials, which have relatively low water to binder (W/B) ratio. Adding an internal curing agent, i.e., superabsorbent polymer (SAP), could be a viable solution in this context. However, employing SAP (without adding additional water) may also influence the fresh properties of LC3 composites by increasing yield stress and viscosity, which may be beneficial for 3D printability. Therefore, this study attempts to use SAP as a rheology modifying admixture with the aim of investigating the impact of SAP on flow behavior, structural build-up, hydration kinetics, compressive strength, and autogenous shrinkage of LC3 pastes with a fixed W/B (0.3). In addition, hydroxypropyl methylcellulose (a typical rheology/viscosity modifier in 3D printable cementitious materials) was also employed in two mixtures to compare their effects. Results show that adding SAP increases the dynamic yield stress and the apparent viscosity, as well as structural build-up and hydration, but decreases the compressive strength at 3, 7 and 28 days. Furthermore, using SAP (especially 0.2 wt % SAP) not only promotes the early-age expansion but also effectively mitigates the autogenous shrinkage of LC3 pastes for up to 7 days. Overall, the obtained results indicated that SAP could act as a promising rheology modifier for the development of 3D printable cementitious materials.
Abstract The global shift towards sustainability has driven significant advancements in construction methodologies. Among these innovations, 3D Concrete Printing (3DCP) stands out as a transformative technology that employs gantry robots to create intricate structures while significantly reducing carbon emissions. Recycling Waste Glass Powder (WGP) as a partial cement substitute addresses two major challenges: reducing landfill waste and enhancing concrete properties. This dual-purpose process transforms waste into value-added materials, thereby contributing to cost-effective, environmentally friendly construction practices. This paper offers a comprehensive review of the literature on WGP applications in 3DCP. It explores WGP’s impact on key concrete attributes, including workability, fluidity, buildability, printability, rheological parameters, compressive strength, flexural strength, and drying shrinkage. Microstructural analysis through scanning electron microscopy (SEM) provides additional insights, elucidating WGP’s role in improving concrete’s performance. The findings demonstrate that incorporating WGP in precise proportions enhances both the fresh and hardened properties of concrete, paving the way for more sustainable and advanced 3DCP applications. The paper concludes with actionable recommendations and outlines prospective research directions for utilizing green WGP-based construction materials, with a particular focus on optimizing their integration into 3DCP technology.
No abstract available
The article presents the results of an experimental study of the influence of technological parameters of construction 3D concrete printing (3DCP) on the durability of printed elements of building structures during accelerated model aging in a climatic chamber. The aim of the work was to study the patterns of degradation of multilayer concrete samples printed on a construction 3D printer in various ways (with and without layer bonding, as well as with cold joint modeling) under cyclic climatic influences. For the experiments, an industrially produced composition of the material for additive construction production 3D4Art was used, applied by a workshop construction 3D printer of a portal design. The control group consisted of monolithic samples of similar geometry. The study included a comparative analysis of the degradation kinetics and mechanisms of destruction of samples during 100 cycles of combined exposure to freezing thawing with humidification. The results demonstrate that while maintaining the overall structural integrity of all samples, 3D printed elements exhibit an increased tendency to crack formation in the areas of interlayer contacts, which is especially pronounced in the case of technological defects (cold seam). The obtained data emphasizes the need for further research into the influence of technologically conditioned defects on changes in the mechanical properties of structural elements during aging. The results of the work are of practical importance for optimizing the technological modes of construction 3D printing to increase the durability of erected structures.
Three-Dimensional Concrete Printing (3DCP) is transforming the construction industry by offering faster, more cost-effective, and sustainable building solutions. However, a major challenge that hinders its full potential is the low tensile strength of concrete, which, as in conventional methods, necessitates reinforcement. Unlike traditional construction, integrating reinforcement into the automated 3D printing process is complex and remains a critical research gap. In this study, zigzag-reinforcing method, that could be classified as an in-process interlayer reinforcement in 3DCP, is proposed. To investigate the effect of the proposed reinforcement technique, an analytical study was conducted using Abaqus finite-element software. Four beam models with different reinforcement configurations were considered: an unreinforced control specimen, two Nitinol-reinforced beams (one exhibiting superelastic behavior and the other the shape memory effect), and a steel-reinforced beam. Three-point bending tests were simulated using a displacement-controlled, centrally applied load. The results showed that zigzag reinforcement improved flexibility and prevented sudden failure. The Nitinol-reinforced sample with superelastic behavior failed at a displacement of 2.67 mm, approximately 37 times greater than the 0.07 mm failure displacement of the unreinforced beam. Unlike the unreinforced specimen, where cracks propagated vertically, the zigzag reinforcement redirected crack propagation horizontally, allowing the beams to carry more load. Additionally, the steel-reinforced sample demonstrated a 68% increase in maximum flexural moment and a 286% increase in flexibility compared to the control specimen. Overall, zigzag reinforcement significantly enhanced the mechanical performance of the samples, and if its durability and other practical parameters are validated through experimental studies, it could be considered a promising reinforcement technique for use in 3D concrete printing.
No abstract available
No abstract available
The structural use of three-dimensional concrete printing remains limited by the directional weakness introduced during extrusion and layer-by-layer deposition. Although 3DPC offers major advantages in formwork elimination, architectural freedom, and automated construction, its printed architecture produces interfaces, pore networks, and reinforcement discontinuities that do not exist in the same form in conventionally cast concrete. This review examines the anisotropic behavior of 3DPC by linking its architectural arrangement, physical interlayer mechanisms, and chemical durability-related processes. The analysis shows that anisotropy develops from the combined effects of filament orientation, interlayer bonding quality, pore morphology, cold-joint formation, mechanical interlocking, hydration continuity, and reinforcement limitations. Weak interlayer regions act not only as preferred paths for crack initiation and propagation under tensile, flexural, shear, and compressive loading, but also as transport channels that accelerate water absorption, chloride ingress, carbonation, sulfate attack, and freeze–thaw deterioration. The review further highlights that fiber, textile, FRP, and discrete reinforcement strategies can reduce some consequences of anisotropy, but their effectiveness depends on whether they bridge the weaker interlayer regions rather than merely reinforcing the filament direction. SEM-based observations confirm that microstructural discontinuities, fiber-matrix debonding, irregular hydration products, and connected pores provide the material-level basis for the directional response of printed concrete. Overall, anisotropy should be treated as a design-critical feature of 3DPC rather than as a secondary defect. Reliable structural application requires coordinated control of mixture rheology, deposition parameters, interlayer timing, curing, toolpath design, and reinforcement layout.
A conformance evaluation of three-dimensionally printed concrete (3DCP) is presented. Interlayer bond and compressive strengths were assessed using standard British and European testing methods to evaluate the suitability of printed specimens for mechanical conformance. The study aimed to examine how well printed concrete aligns with established quality benchmarks and to explore the influence of interlayer bonding on performance. Results showed that the printed elements achieved satisfactory strength and cohesion, with only moderate reductions compared to conventional cast concrete. Although the sample size was limited, the observed behavior and crack patterns reflected stable layer integration and consistent mechanical performance. The findings highlight the feasibility of applying standardized testing procedures to 3D-printed concrete and emphasize the importance of interlayer bond quality in ensuring structural reliability and long-term durability of printed elements.
3D-printed concrete (3DPC) enables formwork-free automated construction with geometric flexibility and improved material efficiency, yet its engineering reliability remains limited by interlayer weakening generated during sequential deposition. This review critically examines the formation, cross-scale consequences, and control of weak interlayer interfaces in 3DPC. In most studies, the 3DPC printing interval ranges from 20 s to 120 min, and the average interfacial bond strength ranges from 0.1 to 16 MPa. Interfacial weakness arises from the asynchronous evolution of adjacent layers in terms of contact quality, rheological recovery, moisture exchange, and early-age hydration. This mismatch promotes pore enrichment, discontinuity of hydration products, reduced phase continuity, and consequent local mechanical softening. These defects govern interlayer bonding, crack propagation, anisotropy, and stress-transfer pathways, and their effects propagate from material properties to member response, structural performance, and durability degradation. Rather than treating the interface as a localized cold joint, this review frames it as a process-induced multiscale variable linking printing history, microstructure, mechanical response, transport behavior, and serviceability. Current research remains constrained by non-comparable testing methods, undefined quantitative thresholds, and models that still rely heavily on empirical calibration. Future work should establish standardized characterization, transferable interface descriptors, multiscale predictive models, real-time quality control, and design methods that explicitly incorporate interfacial variability.
Abstract In Brazil, research on 3D-printed mortar remains nascent, with limited progress in structural applications. In this context, the present study aims to evaluate the structural impact of the printing direction on 3D-printed mortar beams. The study compares three types of beams: those printed in the longitudinal direction, those printed in the transverse direction, and conventionally cast beams. All beams were longitudinally reinforced and subjected to flexural testing. As anticipated, the cast beams exhibited superior strength compared to the beams printed with layers oriented longitudinally along the beam's axis. Beams printed with layers in the transverse direction demonstrated a significant reduction in strength, attributed to weakened interlayer bonding, creating preferential crack propagation paths.
No abstract available
Interlayer bonding strength (IBS) plays a pivotal role in 3D-printed concrete (3DPC), emphasizing the need for a reliable predictive model. A new hybrid model is proposed in this study, which leverages the gorilla troops optimizer (GTO) to fine-tune the hyperparameters of the extreme gradient boosting (XGBoost) algorithm. For comparison, XGBoost and decision tree (DT) models were also developed. To enhance interpretability, SHapley Additive exPlanations (SHAP) were employed to highlight the most influential factors affecting IBS. The proposed GTO-XGBoost model outperformed the other approaches, attaining a correlation coefficient of 0.974, compared to 0.958 for XGBoost and 0.930 for DT. The findings demonstrate that the GTO-XGBoost model offers a reliable solution for predicting IBS, contributing to the advancement of 3D printing technology in construction.
No abstract available
No abstract available
No abstract available
The process of printing in layers stacked on top of each other without the need for formwork in three-dimensional concrete printing makes the bonding at the interlayer interface very important, as it governs the structural performance and long-term durability of additively manufactured concrete elements. Weakening of the adhesive bond can lead to structural failure, reduced durability, and the risk of collapse. Bonding behavior at layer interfaces is influenced by several factors, including printing parameters, the printability of the material, water retention, and the shrinkage behavior of the 3D printable concrete material. This study investigates improving the adhesive bond between 3D printed concrete layers on a rectangular block of size 400 × 400x180 mm which were printed with various concrete mixtures. The concrete used in this research includes Ordinary Portland cement, limestone powder, river sand, water, and superplasticizer. Water-to-binder proportions of 0.30, 0.34, and 0.40 were adopted; superplasticizer content was various as 0.22%, 0.16%, and 0.10% respectively by the weight of cement. Experimental findings indicate that the block printed with the concrete having a water-to-binder ratio of 0.30 and superplasticizer content of 0.22% achieved the best improvement in the adhesive bond between the printed layers. Moreover, incorporating limestone powder at levels up to 10% by cement mass enhances water retention in the fresh mixture, mitigates shrinkage, and strengthens bonding at the interfaces of additively manufactured concrete layers. Especially, the adhesive bond between printed layers of the block was enhance by a combination of addition of limestone powder to concrete mix with a low water-to-binder proportion containing superplasticizer. Additionally, there was a linear relationship between printed height layer and the quality of layer interface bonding.
No abstract available
No abstract available
No abstract available
No abstract available
Abstract The application of additively manufactured, 3D printed concrete in the construction industry has been gaining attention in recent years. 3D concrete printing (3DCP) has potentials for mass customisation, and off-site and rapid manufacturing of complex structural and architectural components. However, 3DCP has many challenges such as competing rheological requirements, weak interlayer bonding, difficulty in integrating reinforcement, and anisotropic material behaviour. Therefore, material properties of printed concrete are often inferior to traditional mould cast and leading to poor structural performance. Thus, satisfying performance criteria for structural applications is the key challenge of 3DCP, methods for enhancing the material properties of 3DCP are required. This article reviewed the main parameters affecting the performance of 3D printed concrete and discussed potential methods to enhance these properties. Methods investigated in this article include novel reinforcement, material modification, rheology control, nozzle design, process improvements, and interlayer bonding. Lastly, this article discussed the performance of structural elements produced by 3DCP and proposed future research areas to advance this technology in the building industry.
No abstract available
No abstract available
This study examined the mechanical characteristics of 3D printed concrete utilized in sculpture materials, with an emphasis on the incorporation of wood fibers. A series of experiments were conducted to probe into the wood fiber-reinforced 3D printed concrete sculpture materials. Through mechanical and microscopic examinations, the role of flexible fibers in enhancing the bearing capacity of concrete 3D printed components was investigated. The results indicated that an optimal amount of wood fiber addition significantly improved the mechanical properties of the concrete sculpture materials. At the interlayer interface, wood fibers exhibited elongation, thereby mitigating the specimen damage. However, beyond a certain threshold, the mechanical properties tended to decline due to either the agglomeration or direct dislodgment of wood fibers at the interlayer interface, which resulted in an absence of notable deformation. This scenario thereby failed to impede crack propagation. Hydrophobic performance assays revealed an elevation in surface hydrophobicity of 3D printed concrete sculpture materials with the inclusion of wood fibers. Yet, an excessive amount of wood fibers caused a gradual reduction in the contact angle, implying a decrease in the hydrophobicity of the material surface.
Flexural strength (FS) governs the structural performance of 3D-printed concrete (3DPC) under bending loads yet remains difficult to predict owing to the coupled influence of binder composition, supplementary cementitious materials, water-to-binder ratio, and fiber reinforcement geometry on interlayer fracture behavior. Much of this compositional diversity stems from supplementary cementitious materials, industrial by-products whose reuse as partial cement replacement lowers the embodied carbon of printable mixes. A machine learning framework was trained on 209 FS records covering OPC- and SAC-based systems (FS: 3.65–45.0 MPa; W/B: 0.15–0.65). Six composite features were constructed from physical principles, two of them specific to bending: Fiber_Pullout_Index encoding post-crack pullout energy and Binder_Efficiency capturing cement quality per unit water content at the fiber–matrix interface; Lasso regularization with the one-standard-error rule reduced the 19-variable space to 14 active predictors. Twenty regression algorithms spanning eight families were benchmarked under 30 independent partitions; the Friedman test rejected equal performance (χ2=337.02, p=4.88×10−60) and all 19 pairwise Wilcoxon comparisons against CatBoost were Holm-significant. CatBoost ranked first (mean rank of 18.17/20; 30-run R2=0.9302±0.0722; seed-42 partition: R2=0.9557; RMSE = 1.761 MPa; MAPE = 11.20%). n(W/B) emerged as the primary driver across SHAP, ALE and LIME, with a monotonic ALE profile spanning 8.99 MPa and no inflection over the full printable window; Binder_Efficiency ranked second (PDP range: 5.21 MPa), isolating cement grade and paste dilution as independent strength levers. Cross-conformal prediction provided finite-sample coverage guarantees without distributional assumptions (empirical coverage: 95.24%; conformity quantile: 3.83 MPa); bootstrap analysis put the epistemic component at a mean predictive SD of 0.946 MPa, a quarter of that quantile. External validation yielded R2=0.769 (Pearson R=0.923, RMSE = 1.91 MPa), with 19 of 20 predictions (95.0%) within Bland–Altman 95% limits of agreement, confirming transfer to a source study withheld from model training. A graphical user interface packaging the 14-feature CatBoost pipeline supports mix design queries without programming.
This study investigates the impact of varying steel fiber (SF) content (0%, 0.8%, 1.0%, and 1.2% by volume) on the mechanical and durability properties of 3D-printed Ca(OH)2-activated geopolymer concrete (GPC). The addition of 1.2% SF improved flexural strength by 69% at 7 days and 16% at 28 days, while tensile strength more than doubled to 3.75 MPa at 28 days. Although compressive strength remained unaffected at 43 MPa, SF enhanced interlayer bond strength by 20%, which is crucial for layer cohesion in 3D-printed structures. Additionally, the elastic modulus increased by 7%, contributing to improved stiffness. Durability assessments, including autogenous shrinkage and self-induced stress, indicated a slight reduction in shrinkage of SF-reinforced samples, with no significant effect on self-induced stress. Microstructural analysis using scanning electron microscopy (SEM) and X-ray micro-computed tomography (µCT) demonstrated the crack-bridging behavior of steel fibers, enhancing ductility and fracture resistance. There was a slight increase in porosity (5.34%) of SF-reinforced samples without negatively affecting their mechanical properties. Notably, SF improved early-age toughness and controlled crack propagation across printed layers, addressing a critical challenge in 3D-printed concrete. The novelty of this work lies in successfully reinforcing 3D-printed Ca(OH)2-activated GPC with recycled steel fibers, enhancing mechanical properties, interlayer bonding, and durability without compromising printability. This study offers a sustainable reinforcement strategy for 3D printing in construction.
Three-dimensional printed concrete (3DPC) is emerging as a new building material. Due to automation, this method dramatically decreases construction time and material wastage while increasing construction quality. Despite the mentioned benefits, this technology faces various issues. Among these issues, the inability to use steel bars for reinforcement and early age cracking because of the low water-to-binder ratio and high amount of binders can be mentioned. In this regard, due to the superior properties of fiber-reinforced concrete (FRC), such as high first crack strength, tensile strength, improvement ductility, and resistance to shrinkage cracking, one of the effective ways to reinforce the mixture of the 3DPC is to use fibers instead of steel bars. Regarding the mentioned issues, the effects of different fibers, such as steel, carbon fibers and so on, on fresh and mechanical properties and dimensional stabilities of hardened concrete have been reviewed. It is predicted that using fibers, especially hybrid fibers, not only covers the deficiencies of initial cracking of 3DPC, but also can be used instead of steel bars; therefore, this material can play a pivotal role in the construction industry’s future.
No abstract available
No abstract available
The absence of effective reinforcement has hindered the widespread use of 3D-printed concrete. In this study, we propose an innovative in-process embedding technology that enables the simultaneous printing of concrete and flexible fiber-reinforced polymer grids. We investigate the performance of grids as reinforcement in 3D-printed concrete through pull-out and splitting tensile tests to assess the bonding properties between the grids and concrete. Additionally, three-point bending tests were conducted to evaluate the impact of grids on the flexural performance of 3D-printed concrete plates. Test results show that the load-bearing capacity and deflection of 3D-printed concrete plates reinforced with grids increased by approximately 41% and 552%, respectively. However, the voids and reduced contact area caused by the simultaneous printing of the grids weakened the bonding between adjacent concrete layers. Overall, the findings confirm the feasibility of the proposed in-process embedding technology and demonstrate its protential to advance 3D-printed concrete structures through the effective integration of in-processfiber-reinforced polymer reinforcement.
As 3D concrete printing emerges as a transformative construction method, its structural safety remains hindered by unresolved issues of mechanical anisotropy and interlayer defects. To address this, we systematically investigate the failure mechanisms and mechanical performance of basalt fiber-reinforced 3D-printed magnesite concrete. A total of 30 cube specimens (50 mm × 50 mm × 50 mm)—comprising three types (Corner, Stripe, and R-a-p)—were fabricated and tested under compressive and splitting tensile loading along three orthogonal directions using a 2000 kN electro-hydraulic testing machine. The results indicate that 3D-printed concrete exhibits significantly lower strength than cast-in-place concrete, which is attributed to weak interfacial bonds and interlayer pores. Notably, the R-a-p specimen’s Z-direction compressive strength is 38.7% lower than its Y-direction counterpart. To complement the mechanical tests, DIC, CT scanning, and SEM analyses were conducted to explore crack development, internal defect morphology, and microstructure. A finite element model based on the experimental data successfully reproduced the observed failure processes. This study not only enhances our understanding of anisotropic behavior in 3D-printed concrete but also offers practical insights for print-path optimization and sustainable structural design.
No abstract available
No abstract available
This study proposes a novel semi-discrete model of non-ordinary state-based peridynamics. It is used to simulate the tensile failure process of dog bone-shaped specimens of 3D-printed fiber-reinforced concrete with 0%, 1% and 2% fiber volume fractions. The results are compared with the literature laboratory results to verify the feasibility and reliability of the approach. In addition, it is utilized for a 3D-printable engineered cement-based composite (ECC) disk splitting simulation. Effects of different fiber lengths, printing interfaces, and fiber orientations on the failure process of disc specimens are investigated. It is found that ductile failure appears in the loading direction, while brittle failure appears in the other direction. Effect of fiber length on the bearing capacity is feeble. In addition, the non-ordinary state-based peridynamics semi-discrete model is used to simulate the crack propagation of three-point bending. The principal stress contours, damage diagrams, and displacement–load curves of the concrete matrix at different time steps during the crack propagation process are obtained. The simulation is in great agreement with the experimental results. Finally, it is demonstrated that the novel non-ordinary state-based peridynamics approach proposed in this paper is accurate and efficient to simulate fracture behavior of 3D-printed ECC beams.
Additive manufacturing of cementitious materials is a rapidly growing branch of manufacturing both in research and industry, particularly the variant of material deposition by extrusion. This process results in a strong anisotropy in mechanical properties, owing largely to the interfaces between adjacent filaments. This anisotropy is even more pronounced when fiber reinforced mortars or continuous entrained reinforcement components such as cables are used. To exploit orientation-dependent performance, the print path can be designed to align with the principal (tensile) stress trajectories. However, obtaining an appropriate print path based on this concept poses several challenges, related to the filling of intermediate spaces between two trajectories. In this paper, an approach for planning such a robot toolpath is presented, elaborated, and illustrated by means of a case study on a well-known reference case. The main features of the tool planning method are the relaxation of the offset width, the avoidance of toolpaths with acute angles by intersecting offset curves, and a continuous toolpath.
No abstract available
With rapid global urbanization and economic development, 3D concrete printing (3DCP) technology has emerged as an innovative construction method, garnering increasing attention and application. Compared to traditional construction techniques, 3DCP not only reduces resource waste and carbon emissions during the building process but also significantly enhances construction efficiency, demonstrating considerable potential in the construction industry. As 3DCP advances from theoretical studies to real-world applications, providing stable and reliable structural reinforcement solutions becomes essential. This paper focuses on examining various methods to improve the performance of 3D-printed concrete (3DPC) structures. The analysis shows that reinforcement using steel bars, in combination with other materials (mainly fibers and nanomaterials), remains a key strategy for structural enhancement. By integrating diverse reinforcement methods, this study proposes an innovative bidirectional steel mesh layout scheme. Additionally, given the unique nature of 3DPC construction, a critical review of various methods for improving interface bonding strength is included. These findings aim to guide the engineering community in selecting suitable reinforcement solutions for 3DPC.
No abstract available
No abstract available
No abstract available
Efficient alkali-activated binder pastes of slag and fly ash-based aqueous nano-silica (FABANS) that provide enhanced strength are used for developing extrusion-based 3D printable concretes. The binder pastes of slag made with FABANS are not suitable for printing due to low yield stress and insufficient thixotropic buildup. Rheology control for enhancing the yield stress and thixotropic buildup is evaluated using bentonite clay and carboxymethyl cellulose (CMC). There is a synergistic enhancement in yield stress and thixotropic buildup provided by the combined use of bentonite and CMC that provides improved printability and buildability. Very rapid increase in yield stress with excess clay content in the presence of CMC, however, produces choking of flow and printability loss. Excess CMC results in a Maxwell-type behavior causing shape instability due to continuous relaxation under stress. The proportion of CMC and clay that provides the required thixotropic buildup for buildability is established. Printability and buildability of concrete mixture made with binder paste of FABANS with the proportion of rheology modifiers is demonstrated.
Extrusion-based three-dimensional concrete printing (3DCP) has emerged as a promising digital construction technology that requires precise control of material rheology and structural performance. This study investigates the influence of steel fibre dosage on the rheological behaviour, mechanical performance, and potential printability of cement-based materials. Mortar mixtures incorporating straight copper-coated steel fibres at dosages from 0 to 1.0% were evaluated. Rheological properties, including yield stress, plastic viscosity, thixotropy, structuration rate, re-flocculation rate, viscosity recovery, and flow index were characterised using rotational rheometry, while compressive and flexural strength were measured at 14 and 28 days. Results show that steel fibres significantly enhance structural build-up and recovery, with both static and dynamic yield stress increasing markedly with fibre dosage. Plastic viscosity and flow behaviour indicate increased resistance to flow at higher contents. Compressive strength exhibits a non-monotonic trend, reaching a maximum increase of approximately 40% at 0.2%, whereas flexural strength is improved at higher fibre dosages due to crack-bridging effects. A normalisation-based composite index was applied to integrate performance indicators. Based on rheology-derived printability implications, a practical working window was proposed, including static yield stress of approximately 280 to 400 Pa, dynamic yield stress of 70 to 160 Pa, plastic viscosity of 7 to 15 Pa·s, re-flocculation rate of 40 to 55 Pa/min and flow index of 0.6 to 1.0. Although higher fibre dosages produced higher composite index values due to dominant rheological enhancement, excessive rheological resistance may reduce practical processability. Based on the proposed working window, 0.2% steel fibre provides the most balanced performance for potential large-scale 3DCP applications.
No abstract available
No abstract available
No abstract available
This research aims to utilize the inherent setting mechanisms of cement to 3D print a more conventional concrete mix without the addition of commercial accelerator admixtures, towards improved surface finish, pumpability or buildability. Three potential rapid setting mechanisms are investigated in this research, namely: flash setting, false setting and belitic calcium sulfoaluminate (BCSA) replacement of cement. The three rapid setting mechanisms are characterised by determining hardened state compressive strength, setting time and green-state compressive strength. Potential mixtures are then 3D printed and their performance quantified through buildability tests and observation of surface finish quality. Additionally, the economic feasibility is investigated. It is shown that false setting does not significantly influence the mechanical properties, while the early age strength gain is not as rapid as for flash setting or BCSA cement. Flash setting improves the early age strength but reduces the long-term compressive strength. Partially replacing OPC with BCSA cement improves the early age strength and does not impact the mechanical properties significantly. Higher cement replacements increased the intensity of the rapid setting mechanisms, shortening setting and increasing early age strength. Flash setting showed the largest positive impact on the buildability of 3D printed concrete. The buildability could be increased by 321% with flash setting, while BCSA cement resulted in a buildability increase of 214% and for false setting only a 35% increase. Flash setting and BCSA replacement are shown to be the more economical rapid setting mechanisms.
The utilization of supplementary cementitious materials (SCMs) to reduce the Portland‐cement fraction is of growing interest in 3D concrete printing. This study investigates the fresh‐state, rheological, printability, buildability, and mechanical performance of a GGBFS–silica fume blended cementitious composite developed for extrusion‐based 3D concrete printing (3DCP). The printable mixture comprised 472.5 kg/m 3 ordinary Portland cement, 182.5 kg/m 3 ground granulated blast‐furnace slag (GGBFS), and 75 kg/m 3 silica fume, with SCMs constituting 35.27% of the total binder. Fresh‐state characterization showed an initial flow diameter of 172 mm and a flow‐based practical open time of approximately 45 min. Stable extrusion was achieved with an average filament width of 21.2 mm and an extrudability index of 1.06. Rheological characterization using the Herschel–Bulkley model showed good agreement with the experimental data ( R 2 = 0.97), while penetration‐derived static yield stress increased from 0.48 to 3.21 kPa over 75 min, consistent with progressive time‐dependent structural build‐up under the adopted test arrangement. The mixture successfully produced a 50‐layer wall element without collapse, with a height deviation of 2.72% under the investigated printing conditions. After 28 days of curing, the printed composite achieved an average compressive strength of 41.8 MPa and an average flexural strength of 6.0 MPa, with modest numerical variation among the investigated loading orientations. The findings indicate that the selected formulation containing 35.27% supplementary cementitious materials exhibited continuous extrusion, successful 50‐layer wall fabrication, and the measured mechanical performance under the investigated printing conditions. The 35.27% SCM incorporation represents a reduction in the Portland‐cement fraction.
Early-age deformation is a major limitation on the buildability of extrusion-based 3D-printed concrete because each deposited layer must carry increasing self-weight while hydration, thixotropic rebuilding, stiffness, and strength are still evolving. This survey reviews experimental, rheological, analytical, and numerical approaches used to characterize and predict creep and related deformation during printing. The reviewed experiments include compression, creep-recovery, digital image correlation, and full-scale printing tests. Analytical approaches include Burgers, generalized Kelvin, power-law, and hydration-coupled viscoelastic formulations, whereas numerical studies employ continuum finite elements, lattice and voxel activation, damage-rheology laws, particle finite elements, computational fluid dynamics, and coupled fluid-solid models. Across these approaches, predicted buildability depends strongly on material age at loading, load duration, deposition interval, layer geometry, and interface behavior. The literature shows that elastic models are useful for rapid screening, but viscoelastic, plastic, or damage mechanisms become important when printing duration is long or stress approaches the evolving resistance. Remaining priorities are standardized early-age tests, independent validation, uncertainty quantification, and transferable models that connect material characterization with layer-by-layer structural analysis.
No abstract available
One of the most significant challenges for 3D printing of construction elements from cementitious materials is the control of cracking caused by various contraction–shrinkage mechanisms, such as drying, chemical, plastic and autogenous shrinkage. This study addresses the effects of incorporating fine aggregates (maximum size ≤ 1.18 mm), both natural and recycled, as well as short (6 mm long) polypropylene (PP) fibres on the control of cracking in cementitious mixtures based on Portland cement. Admixtures and/or mineral additions (modifiers), such as metakaolin, micro-silica, calcium carbonate, and fine powders obtained from construction and demolition wastes were used in the mixtures. Mini-slump, flow rate and buildability tests were used to characterize the mixtures in their fresh state. Extrudability was evaluated using laboratory-scale 3D printing tests conducted with a plunger–piston extrusion system. It was demonstrated that the physical characteristics of the aggregates directly influence the extrusion capacity. Mixtures containing natural aggregates exhibited greater fluidity and lower water demand than those containing recycled aggregates. The results indicated that the maximum allowable volume of fibres was 0.75%. To evaluate the cracking susceptibility of the mixtures, both with and without reinforcement, hollow beams composed of seven layers were printed, and subsequently the elements were exposed to the outdoor natural environment and inspected for a period of 90 days. The inclusion of the PP fibres effectively prevented the occurrence of fissures and/or cracks associated with shrinkage phenomena throughout the inspection period, unlike in unreinforced mixtures, which cracked after 14 days of exposure to the environment.
No abstract available
No abstract available
Three-dimensional concrete printing (3DCP) is an emerging additive manufacturing technology with increasing application potential in the construction industry, offering advantages such as reduced labor requirements, shortened construction time, and material efficiency. However, structural integrity remains a challenge, particularly due to weak interlayer bonding resulting from the layered manufacturing process. This study investigates the mechanical performance and anisotropy of 3D-printed mineral-based composites with respect to the time interval between successive layers. Specimens were printed with varying interlayer intervals (0, 25, and 50 min) and tested in different loading directions. Flexural, compressive, and tensile strengths (direct and splitting methods) were measured both parallel and perpendicular to the layer orientation. Results showed a clear degradation in mechanical properties with increasing interlayer time, particularly in the direction perpendicular to the layers. Flexural strength decreased by over 25% and direct tensile strength by up to 40% with a 25 min interval. Compressive strength also declined, though less dramatically. Compared to cast specimens, printed elements showed 3–4 times lower compressive strength, highlighting the significant impact of interlayer cohesion. This study confirms that both the time between layers and the loading direction strongly influence mechanical behavior, underlining the anisotropic nature of 3DCP elements and the need for process optimization to ensure structural reliability.
This study investigates the structural behaviour of elements produced by extrusion-based 3D concrete printing (3DCP). Six full-scale columns with intentional imperfections were tested in three-point bending and subsequently analysed through fragment testing. Compressive strength (16.6–32.2 MPa), flexural tensile strength (1.96 MPa parallel vs. 1.27 MPa perpendicular), ultrasonic pulse velocity, bulk density, and water absorption were measured. The results confirmed pronounced anisotropy and strong correlations between physical and mechanical properties. A simplified FEM model, calibrated with fragment data, reproduced global stiffness but not brittle delamination. The combined methodology offers a basis for diagnostics and quality control of 3DCP elements.
Abstract 3D concrete printing has tremendous potential for construction manufacturing; however, weak interface bonding between adjacent layers remains a well-known issue that affects the mechanical properties of printed structures. The layers introduce anisotropy and reduce the capacity to resist tensile and shear loads. Reinforcements, inserted perpendicular to the printed layers to traverse the interfaces, can improve these limitations, but the insertion of reinforcements is difficult to achieve in practice, and there are few published studies exploring appropriate methods. This study presents a promising approach using U-shaped nails inserted into concrete during the printing process. The bridging effect and dowel action of the applied U-nails are visualised and analysed to elucidate the toughness improvement. The ultimate tensile strength and shear strength of 3D printed concrete are significantly increased by 145.0% and 220.0%, respectively. U-nails with a filament thickness of 2–2.5 mm are recommended to yield optimal improvement in the interlayer strength.
No abstract available
3D-printed ultra-high-performance concrete (3DP-UHPC), which combines high strength, high toughness, and construction flexibility, provides a solution to the reinforcement difficulty of conventional printed concrete. However, the layer-by-layer printing process induces pronounced anisotropy in compressive and flexural properties, which remains a key challenge for engineering applications. We used X-ray computed tomography (X-CT) to quantitatively analyse the internal pores and to reveal the orientation and distribution of steel fibres in 3DP-UHPC. Splitting tensile tests showed that the interlayer splitting tensile strength is approximately 49.3% lower than the conventional splitting tensile strength, and increasing fibre content has a limited strengthening effect. Analysis of the compressive anisotropy index \( \lambda_\text{c} \) indicates that, at \( V_\text{f} = 0% \), anisotropy is mainly influenced by weak interlayer interfaces and pore distribution. Linear fitting shows that a small fibre addition (\( V_\text{f} \leq 1.28% \)) reduces compressive anisotropy, whereas higher \( V_\text{f} \) leads to an increase in \( \lambda_\text{c} \) due to fibre orientation. For the flexural anisotropy index \( \lambda_\text{f} \), interstrip interfaces and pores dominate at \( V_\text{f} = 0% \) and \( 0.5% \), while fibre distribution governs \( \lambda_\text{f} \) when \( V_\text{f} \geq 1.0% \), with an increase exceeding 60%. Within \( V_\text{f} = 0%-2.0% \), \( \lambda_\text{c} \) remains higher than \( \lambda_\text{f} \), indicating relatively stable compressive performance. These results provide experimental evidence for optimising the compressive and flexural performance of 3DP-UHPC components in engineering applications.
Failure mechanisms of 3D-printed laminates reinforced with fibers are investigated. In order to clarify the effects of layered anisotropy in mortar filaments, compressive tests are conducted using specimens with end constraint under various loading rates. The specimens are cored-drilled in three directions from a laminated body fabricated by 3D printed, as well as those cast in a formwork. By reducing end-constraints, tensile stress is induced at the layer interfaces, and thus the interfacial fracture process is observed by using the Digital Image Correlation (DIC) method. In the coredrilled specimens, it was observed that the stresses drop sharply before reaching the maximum stress, followed by a subsequent recovery in loadbearing capacity. DIC confirmed that cracking initiated at the interfaces. These results were different from the specimens cast in the formwork. It is found that the interfacial failure of laminated mortar depends on the adhesion strength between the filaments. Thus, two-stage failure process is elucidated as an initial brittle fracture along a weak layer interface, followed by a tenacious post-peak response.
Abstract This study developed a novel ultra-high ductile concrete (UHDC) for 3D concrete printing, which was modified using crumb rubber to possess high ductility. Flowability tests were conducted to determine optimal open time range for continuous printing. A series of mechanical tests, including uniaxial tensile test, compressive test, flexural test and double shear test, were carried out to investigate the anisotropic-mechanical properties of the printed UHDC. The results indicate that the tensile strength, flexural strength and shear strength of the printed specimens were slightly lower than those of mold-cast specimens, while reverse tendency was observed in compressive strength. It is of interest that the deformability and energy dissipation of the printed UHDC at some directions are higher than those of mold-cast UHDC. Additionally, it is found that the printed UHDC performed minimal anisotropy in flexural strength, but significant anisotropy in flexural deformability, compressive and flexural energy dissipation capacity.
This paper discusses the flexural and tensile strength properties of 3D printed concrete, based on the results of a RILEM TC 304-ADC interlaboratory study on mechanical properties. These properties are determined using different testing techniques, including 3- and 4-point flexural tests, splitting tests, and uniaxial tension tests, on specimens extracted from large 3D printed elements in accordance with a prescribed study plan. The relationship between compressive and flexural or tensile strengths, cast or printed samples, different types of tests, and different loading orientations, are analysed to understand the influence of 3D printing. As expected, the strength can reduce significantly when the main tensile stress is acting perpendicular to the interface between layers. The role of deviations from the standard study procedure, in terms of the time interval between the placing of subsequent layers, or the adoption of a different curing strategy, are also assessed. While the increased time interval significantly impacts the strength in the critical direction, the use of variable curing conditions does not seem to have a clear-cut effect on the strength ratios of the printed to cast specimens. Additionally, the paper looks at the variability in the results for the printed specimens, in order to emphasize the need for multiple replicates for obtaining a proper result. An extensive insight into the aspects affecting the variability is presented in the paper. Finally, with the limited dataset available for specimens tested at a larger scale, it is difficult to arrive at a clear understanding of the role of specimen size (i.e., greater number of layers).
No abstract available
No abstract available
The additive manufacturing of concrete, also known as 3D-printed concrete, is produced layer by layer using a 3D printer. The three-dimensional printing of concrete offers several benefits compared to conventional concrete construction, such as reduced labor costs and wastage of materials. It can also be used to build complex structures with high precision and accuracy. However, optimizing the mix design of 3D-printed concrete is challenging, involving numerous factors and extensive hit-and-trail experimentation. This study addresses this issue by developing predictive models, such as the Gaussian Process Regression model, Decision Tree Regression model, Support Vector Machine model, and XGBoost Regression models. The input parameters were water (Kg/m3), cement (Kg/m3), silica fume (Kg/m3), fly ash (Kg/m3), coarse aggregate (Kg/m3 & mm for diameter), fine aggregate (Kg/m3 & mm for diameter), viscosity modifying agent (Kg/m3), fibers (Kg/m3), fiber properties (mm for diameter and MPa for strength), print speed (mm/sec), and nozzle area (mm2), while target properties were the flexural and tensile strength of concrete (MPa data from 25 literature studies were collected. The water/binder ratio used in the dataset ranged from 0.27 to 0.67. Different types of sands and fibers have been used, with fibers having a maximum length of 23 mm. Based upon the Coefficient of Determination (R2), Root Mean Square Error (RMSE), Mean Square Error (MSE), and Mean Absolute Error (MAE) for casted and printed concrete, the SVM model performed better than other models. All models’ cast and printed flexural strength values were also correlated. The model’s performance has also been checked on six different mix proportions from the dataset to show its accuracy. It is worth noting that the lack of ML-based predictive models for the flexural and tensile properties of 3D-printed concrete in the literature makes this study a novel innovation in the field. This model could reduce the computational and experimental effort required to formulate the mixed design of printed concrete.
No abstract available
No abstract available
Abstract Refined methodology for numerical stress-strain analysis of 3D-printed concrete (3DPC) structures using ANSYS is presented. The model integrates a nonlocal microplane theory for concrete layers and a Cohesive Zone Model (CZM) for interlayer behavior. Material parameters were determined experimentally: concrete properties via uniaxial compression/tensile tests on cast samples, and interlayer properties via tangential splitting tests on unreinforced 3DPC. Four-point bending tests on reinforced 3DPC samples, loaded across and along layers, evaluated mechanical behavior and validated the model. The verified model predicted strength characteristics for 72 structural variants, differing in reinforcement (type, strength, area, percentage) and layer thickness. High convergence between numerical and experimental results was achieved, with deviations in ultimate and crack initiation stresses below 15%. Simulations accurately described stress distribution in bent elements, matching observed crack propagation and confirming pronounced anisotropic behavior dependent on loading direction relative to layers. This methodology provides a robust tool for virtual modeling, enabling reliable prediction of 3DPC structural response in CAE software.
No abstract available
No abstract available
3D Concrete Printing (3DPC) enables the fabrication of geometrically complex lattice structures, and Selective Paste Intrusion (SPI) technology further extends this capability to precisely control internal architectures. This study presents the first numerical validation of the mechanical performance of SPI 3DPC lattice structures at the specimen scale. A finite element framework based on the Concrete Damaged Plasticity (CDP) constitutive model was established to investigate compressive responses of gyroid geometries with varying volume fractions. The results demonstrate good agreement between the numerical model and experimental data in terms of elastic modulus and compressive strength. The simulations also reveal a transition in the localization pattern with increasing volume fraction, from nodal strain localization in the 40% specimen to a continuous diagonal shear band in the 60% specimen, consistent with experimental crack patterns. Parametric analyses further indicate that tensile and compressive strength govern peak capacity, while elastic modulus controls initial stiffness and fracture energy regulates post-peak softening behavior. The viscoplastic regularization parameter is also investigated for its effect on numerical convergence. The proposed framework provides a useful numerical tool for analyzing the mechanical response of SPI 3DPC structures and offers a basis for parameter calibration, structural response assessment, and future multiscale modeling.
The use of nanomaterials (NMs) in 3D printing concrete (3DPC) has shown significant advancements in enhancing both fresh and hardened properties. This review finds that their inclusion in printable concrete has altered the rheological properties of the mix by promoting thixotropy, extrudability, and buildability while simultaneously refining the microstructure to enhance mechanical strength. Studies further highlight that these additives impart functional properties, such as the photocatalytic activity of nano-TiO2, which enables self-cleaning ability and assists pollutant degradation. At the same time, carbon-based materials enhance electrical conductivity, thereby facilitating the development of innovative and multifunctional structures. Such incorporation also mitigates anisotropy by filling voids, creating crack-bridging networks, and reducing pore interconnectivity, thereby improving load distribution and structural cohesion in printed structures. Integrating topology optimisation with 3DPC has the potential to enable efficient material usage. Thus, it enhances both sustainability and cost-effectiveness. However, challenges such as efficient dispersion, agglomeration, energy-intensive production processes, high costs, and ensuring environmental compatibility continue to hinder their widespread adoption in concrete printing. This article emphasises the need for optimised NM dosages, effective dispersion techniques, and standardised testing methods, as well as sustainability considerations, for adapting NMs in concrete printing.
The interlayer pores of 3D-printed concrete (3DPC) significantly weaken its macroscopic mechanical properties. In this study, the phase-field cohesive zone model (PF-CZM) is employed as a numerical tool to systematically investigate the weakening mechanisms and crack evolution behavior associated with pore characteristics, including pore size, morphology, spatial orientation, and arrangement, through single-factor numerical simulations with different pore numbers. The results demonstrate that the degradation induced by a single pore is controlled by its effective projection length in the direction perpendicular to the principal tensile stress, with horizontal flat pores being the most detrimental under the same porosity. In the multi-pore system, the connection angle between pores, rather than their spacing, is the key factor determining structural degradation, and a horizontal collinear arrangement is prone to triggering brittle fracture. Furthermore, locally aggregated small pores can form combined defects, whose strength-weakening effect surpasses that of isolated large pores, thereby triggering crack path competition and leading to asymmetrical structural failure. This study reveals the fracture mechanisms driven by complex pore configurations and provides a reference for strength prediction of 3DPC.
Earth-based 3D printed concrete (3DPC) was developed using soil as an alternative to fine aggregates. Locally sourced excavated soil with 4% clay content was used to replace 30–50% of natural sand by weight, as a partial replacement and as an additive. The effect of soil inclusion on the fresh and hardened properties of 3DPC was analyzed. The inclusion of soil led to a reduction of up to 15% in the flow value required for printing and increased open time by 13–60% compared to the control mix. Both extrudability and buildability improved, enabling crack-free printing of more than 30 layers. Isothermal calorimetry showed accelerated hydration, correlating with faster structuration and extended open time. Green strength results showed that soil inclusion delayed the onset of cracks by 30–50%. Compressive strength and bond load values for printed specimens at 28 days showed a reduction of 11–58% and 3–10%, respectively.
No abstract available
This study investigates the nonlinear in-plane structural behavior of 3D-printed concrete wall elements with two representative internal infill patterns ‒ lattice (L) and triangular (T) ‒ using finite element modeling informed by experimentally derived material properties. A printable concrete mixture was specifically developed using CEM I 42.5 R Portland cement, silica sand, and hydroxypropyl methylcellulose (HPMC) as a viscosity-modifying agent. Conventional cast specimens (40×40×160 mm³) achieved a 28-day flexural strength of 8.7 MPa and a compressive strength of approximately 63 MPa. Nonlinear behavior of wall panels with both infill types was investigated using numerical methods with advanced constitutive laws. These models account for the distinct compressive–tensile response of concrete and damage evolution under monotonic lateral loading, allowing assessment of the influence of geometry on load-bearing capacity and failure mechanisms. The results reveal that both infill patterns exhibit nonlinear load–displacement responses with an initial elastic regime, an early localized cracking peak, followed by a notable recovery in load-bearing capacity, and subsequently a global peak load prior to progressive post-peak softening. While the overall performance of both infill types was comparable, the T pattern exhibited a marginally higher peak load (1.7–2.7%) and improved ductility relative to the L form. These distinctions are attributed to the T-pattern’s more efficient diagonal force transfer and the development of a single continuous diagonal shear band, as opposed to the L-pattern’s multiple discontinuous cracks and broader damage zones.